Abstract:The effect of coating cracking during depth-sensing indentation testing (e.g. nanoindentation testing) on systems comprising thin hard coatings (e.g. TiN) on a less stiff, hard substrate (e.g. steel) has been investigated in order to establish whether, at such small scales, the occurrence of annular through-thickness cracks around indentation sites can be detected from load–displacement plots and whether any accompanying localized debonding of the coating from the substrate can also be identified. Experiments were performed on thin TiN and NbN monolayers, and compositionally modulated TiN/NbN and TiN/ZrN deposited onto hard steel or stainless steel substrates. Above a critical load (Pcrit) in the range 80–500mN, all systems exhibited annular through-thickness cracks around indentation sites. The cracking was found to be accompanied by a discrete change in gradient of the loading portion of the load–displacement curve. Also, analysis of the unloading curves beyond this point showed that elastic recovery was controlled by the elastic modulus of the underlying substrate material alone. The cracking mechanism has been characterized using scanning electron microscopy, coupled with optical profilometry to map the detailed z-displacement of the surface — a procedure critical to understanding whether coating–substrate debonding had occurred. Some cracks were found to show a spiral morphology and the effect of indentation loading rate was investigated to see if appearance of these cracks was loading-rate sensitive. Our results highlight the problems inherent in assessing both the interfacial failure and the interfacial fracture toughness of thin film coated systems at the small contact scales (⩽1μm) associated with crack genesis where it is difficult to confirm the extent of sub-surface cracks by conventional means. We have also demonstrated that both load–displacement and load–displacement squared plots are necessary if a more complete understanding of system behaviour is to be gained. Also, a simple fracture mechanics model for the annular cracking behaviour seen in such systems has been derived and used to estimate a value of Gic (the interfacial work of fracture) as 180Jm−2 for the TiN/ZrN-stainless steel system.

Evaluation of the Elastic-Plastic Properties of TiN Coating by Nanoindentation Technologies Using FEM-reverse Algorithm

Finite Element Analysis of the Nanomechanics of Hard Coatings on a Soft Polymer Substrate by a Spherical Indenter

Research on Determining Elastic–Plastic Constitutive Parameters of Materials from Load Depth Curves Based on Nanoindentation Technology

Towards Full Ab Initio Simulations of Mechanical Response of Ti-N Binary System under Extremely Operational Conditions Via Neural Network Potential

Estimation of fatigue life of TiN coatings using cyclic micro-impact testing

Mechanical Properties and Fracture Toughness of Multilayer Hard Coatings Using Nanoindentation

Critical Review of Nanoindentation-Based Numerical Methods for Evaluating Elastoplastic Material Properties

Finite element analysis of the critical ratio of coating thickness to indentation depth for coating property measurements by nanoindentation

The effect of the substrate on the mechanical properties of TiN coatings

Direct quantification of mechanical responses of TiSiN/Ag multilayer coatings through uniaxial compression of micropillars

Influence of the Mechanical Properties of Elastoplastic Materials on the Nanoindentation Loading Response

Indentation stress–strain analysis and finite element simulation to determine elastoplastic properties of thin films decreasing the substrate contribution

Microstructure Evolution-Dominated Mechanical Properties of Pure Titanium under Nanoindentation

Determining the Constitutive Properties of Sintered Nano Silver via Reverse Analysis and Nanoindentation

The effect of coating cracking on the indentation response of thin hard-coated systems

Superelasticity of Tini Thin Films Induced by Cyclic Nanoindentation Deformation at Nanoscale

Effects of Elastic Modulus Mismatch Between Coating and Substrate on the Friction and Wear Properties of TiN and TiAlN Coating Systems

Identifying the elastoplastic properties of ductile film on hard substrate by nanoindentation

Nanoindentation study and theoretical analysis of elastic behavior of single TiO2 nanobelt and nanotube

Atomistic simulation of tribology behaviors of Ti-based FeCoNiTi high entropy alloy coating during nanoscratching