Dual-mode Arbitrary-Ratio Power Splitter Based on a T-branch Embedded with Nanoholes

Zhongqiu Zhong,Yingjie Liu,Ke Xu

DOI: https://doi.org/10.1364/acpc.2020.m4a.142

2020-01-01

Abstract:A dual-mode power splitter with arbitrary-ratio is designed via a T-branch embedded with nanoholes. The device can operate from 1500 to 1600 nm with excess losses < 0.42 dB and inter-mode crosstalks < ‒15.64 dB.

What problem does this paper attempt to address?

Dual-mode arbitrary-ratio power splitter based on a T-branch embedded with nanoholes

Zhong Zhongqiu,Liu Yingjie,Xu Ke

2020-01-01

Abstract:A dual-mode power splitter with arbitrary-ratio is designed via a T-branch embedded with nanoholes. The device can operate from 1500 to 1600 nm with excess losses < 0.42 dB and inter-mode crosstalks <-15.64 dB. (C) 2020 The Author(s)
Broadband and High Uniformity Y Junction Optical Beam Splitter with Multimode Tapered Branch

Chonglei Sun,Jia Zhao,Zuojia Wang,Liuge Du,Weiping Huang

DOI: https://doi.org/10.1016/j.ijleo.2018.12.013

IF: 3.1

2018-01-01

Optik

Abstract:A high uniformity and broad bandwidth Y junction optical beam splitter is proposed and analyzed in this paper based on silicon-on-insulator platform. By replacing the uniform branch with the multimode tapered branch, the bandwidth and the power uniformity of two output ports are unproved prominently. Furthermore, the sensitivity to fabrication accuracy is reduced by widening the splitting angle. The simulation and the experimental results confirm that the bandwidth is larger than 100 nm, the power uniformity of two output ports is enhanced 4 dB, whereas the insertion loss is less than 0.6 dB and the return loss is larger than 26 dB, respectively.
T-Branch Waveguide Mirror for Multimode Optical Splitter With Arbitrary Power Ratios

Zhongqiu Zhong,Yingjie Liu,Shuai Wang,Yilin Liu,Hongzhi Jin,Qinghai Song,Ke Xu

DOI: https://doi.org/10.1109/JQE.2021.3104851

IF: 2.5

2021-01-01

IEEE Journal of Quantum Electronics

Abstract:Mode-division multiplexing is an enabling technique for large-capacity on-chip optical interconnects. Multimode power splitter becomes the subject of interests which is highly desirable. However, challenges still exist for multimode splitter with arbitrary power ratio. Inspired by geometric optics, we demonstrate a series of power splitters based on T-branch waveguide mirrors which consist of subwavelength nanoholes. Arbitrary split ratio can be achieved by modifying the transmittance and reflectance of the waveguide mirrors. The devices can support up to 9 modes from TE 0 -TE 8 . For a proof-of-concept demonstration, we fabricate dual-mode splitters with power ratios of 40:60, 30:70 and 20:80. For both TE 0 and TE 1 modes, the measured excess losses are lower than 0.92 dB, and the crosstalk are all below -14.42 dB within the wavelength range from 1540 to 1580 nm.
Mid-Infrared, Ultra-Broadband, Low-Loss, Compact Arbitrary Power Splitter Based on Adiabatic Mode Evolution

Jia Xu Brian Sia,Wanjun Wang,Xin Guo,Jin Zhou,Zecen Zhang,Mohamed Said Rouifed,Xiang Li,Zhong Liang Qiao,Chong Yang Liu,Callum Littlejohns,Graham T. Reed,Hong Wang

DOI: https://doi.org/10.1109/jphot.2019.2907788

IF: 2.4

2019-01-01

IEEE Photonics Journal

Abstract:We designed and demonstrated TE-mode arbitrary power splitters based on adiabatic mode evolution. The power splitters are designed with a footprint of smaller than 12 × 2.9 μm2, fabricated on a 400-nm silicon-on-insulator platform, requiring only a single etch step. The optimization process and the conditions for arbitrary-power splitting are performed using three-dimensional-FDTD simulations. We prove this concept through the fabrication of asymmetrical adiabatic evolution-based power splitters with splitting ratios of 50:50, 60:40, and 70:30. The fabricated devices are shown to agree closely with simulation results. Broadband operation with low insertion loss of 0.11–0.6 dB is demonstrated across the 3.66–3.89 μm wavelength range (230 nm). This component has applications in a multitude of areas such as spectroscopic optical sensing and optical phased arrays photonic integrated circuits etc.
Ultra-broadband Dual-Mode 3 Db Power Splitter Based on a Y-junction Assisted with Mode Converters.

Hongnan Xu,Yaocheng Shi

DOI: https://doi.org/10.1364/ol.41.005047

2016-01-01

Abstract:A dual-mode 3 dB power splitter for application in an on-chip mode (de)multiplexing system is proposed and demonstrated. This device is composed of mode converters cascaded with a Y-junction. The simulation results show that ∼50∶50 splitting ratio can be achieved for both TM0 mode and TM1 mode over a wide wavelength range from 1.52 to 1.62 μm. The fabricated device, which consists of a multiplexer, a dual-mode 3 dB power splitter, and a demultiplexer, has insertion losses of 0.54 dB for TM0 mode and 0.86 dB for TM1 mode at 1.55 μm wavelength. The measured cross talk is 15.7 and 17.2 dB at 1.55 μm wavelength for the TM0 mode and TM1 mode, respectively.
Arbitrary-Ratio Power Splitters Using Area Modulation Multimode Interference Couplers

Yl Sun,Xq Jiang,Jy Yang,Mh Wang

DOI: https://doi.org/10.1088/0256-307X/22/10/038

2005-01-01

Chinese Physics Letters

Abstract:We describe a novel compact power splitter with tunable power splitting ratios based on multimode interference couplers employing area modulation in a polymer. The experiments show large tuning ranges with splitting ratio varies from 6.94 to 88:12 and low heating power of 5 m W for pi phase shift.
Ultra-broadband On-Chip Multimode Power Splitter with an Arbitrary Splitting Ratio

Hongnan Xu,Daoxin Dai,Yaocheng Shi

DOI: https://doi.org/10.1364/osac.396024

2020-01-01

OSA Continuum

Abstract:The multimode power splitter is a basic component in mode-division multiplexing systems. In this paper, we propose an ultra-broadband silicon multimode power splitter enabling arbitrary power splitting ratios. The proposed multimode splitter is designed based on a waveguide crossing with an obliquely embedded subwavelength grating (SWG) transflector. The incident multiple guided-modes can be split into two beams with low excess losses and low crosstalk by the SWG transflector where the thin-film interference effect happens. As an example, a silicon multimode power splitter is designed to work with the three lowest-order modes of TE polarization. Any desired splitting ratio ranging from 0% to 100% can be achieved by engineering the structural parameters of the SWG. Moreover, the desired splitting ratio can be very uniform over an extremely broad bandwidth of ≥ 415 nm, covering O-, E-, S-, C-, L- and U-bands. The intermodal crosstalk is < −20 dB for all the input modes in theory. To the best of our knowledge, the proposed structure is the first multimode power splitter enabling any desired power splitting ratios in all the optical communication bands.
Broadband Multimode 3 Db Optical Power Splitter Using Tapered Couplers.

Weiwei Chen,Jian Lin,Hongxiang LI,Pengjun Wang,Shixun Dai,Yuxiao Liu,Runkui Yao,Jun LI,Qiang Fu,Tingge Dai,Jianyi Yang

DOI: https://doi.org/10.1364/oe.471397

IF: 3.8

2022-01-01

Optics Express

Abstract:A design of a 1 × 2 multimode 3 dB optical power splitter using tapered couplers is proposed and investigated in this paper. As an example, a 1 × 2 splitter processing five-lowest order transverse-electric-polarized modes is designed and optimized by utilizing finite difference time domain method and particle swarm optimization algorithm. To verify the feasibility of this novel design, the optimized device is fabricated on a silicon-on-insulator platform. The coupling lengths of tapered couplers are respectively 6.5 µm, 6.0 µm, 3.5 µm, 5.0 µm, 5.0 µm, 7.5 µm, 6.0 µm, 5.0 µm, and 8.0 µm. Measurement results reveal that, for the fabricated splitter, the power uniformity varies from 0.041 to 0.88 dB, the crosstalk ranges from -23.96 to -14.12 dB, and the insertion loss changes from 0.089 to 1.50 dB within a bandwidth from 1520 to 1600 nm.
Ultra Compact and Low Loss Multimode Interferenc Splitter for Arbitrary Power Splitting

Qingzhong Deng,Xinbai Li,Ruobing Chen,Zhiping Zhou

DOI: https://doi.org/10.1109/group4.2014.6961983

2014-01-01

Abstract:Arbitrary power splitting ratio is obtained by an 1-to-2 asymmetric multimode interference splitter. The dimension of the multimode section is less than 1.5μm × 3μm while the excess loss is lower than 0.15 dB.
Broadband Arbitrary Ratio Power Splitters Based on Directional Couplers with Subwavelength Structure

Shi Zhao,Yaocheng Shi

DOI: https://doi.org/10.1109/lpt.2021.3070464

IF: 2.6

2021-01-01

IEEE Photonics Technology Letters

Abstract:We propose an 1×2 power splitter enabling arbitrary splitting ratios based on a directional coupler with subwavelength structure. The simulation results show that arbitrary power splitting can be achieved over a broad bandwidth ~120 nm.
A novel polarization and dichroic dual-functional splitter with ultra-high splitting ratios

Kun Li,Fan Lu,Dalin Liu,Zhijun He

DOI: https://doi.org/10.1364/cleo_at.2014.jw2a.47

2014-01-01

Abstract:A novel polarization and dichroic dual-functional splitter is proposed, with ultra-high polarization splitting ratios >33dB and >36dB for TE- and TM-polarized modes, respectively; and with high wavelength splitting ratios >26dB and >33dB for 650nm and 850nm, respectively.
Ultra-broadband Dual-Polarization and Arbitrary Ratio Power Splitters Based on Bezier Curve Optimized Multimode Interference.

S. H. Zhao,S. H. A. N. G. T. O. N. G. Han,M. I. N. G. Y. U. Zhu,J. I. N. G. Y. E. Chen,Y. A. O. C. H. E. N. G. Shi

DOI: https://doi.org/10.1364/ol.485742

2023-01-01

Abstract:We propose and demonstrate two types of 1 × 2 power splitters based on multimode interference (MMI), which are ultra-compact, fabrication friendly, and low loss. The contours of MMI and output tapers are optimized with Bezier curves, which can implement arbitrary ratio power splitters (ARPSs) and ultra-broadband dual-polarization power splitters (UDPSs). For ARPSs, the experimental results show that arbitrary power splitting ratios can be obtained with an average excess loss (EL) of 0.17 dB at 1550 nm for fundamental TE polarization. For UDPSs, the experimental results show that the ELs for fundamental TE and TM polarization are less than 0.63 dB and 0.44 dB over a large bandwidth of 415 nm (1260–1675 nm). The footprints of the proposed devices are less than 10 µm × 2.5 µm (without input straight waveguide) with large fabrication tolerance.
Ultra-compact and Broadband Polarization-Insensitive Mode-Order Converting Power Splitter

Haoqi Chen,Runkui Yao,Pengjun Wang,Qiang Fu,Weiwei Chen,Shixun Dai,Dejun Kong,Jian Lin,Tao Jin,Jun Li,Tingge Dai,Jianyi Yang

DOI: https://doi.org/10.3788/col202422.031301

IF: 2.56

2024-01-01

Chinese Optics Letters

Abstract:A polarization-insensitive mode-order converting power splitter using a pixelated region is presented and investigated in this paper. As TE0 and TM0 modes are injected into the input port, they are converted into TE1 and TM1 modes, which evenly come out from the two output ports. The finite-difference time-domain method and direct-binary-search optimization algorithm are utilized to optimize structural parameters of the pixelated region to attain small insertion loss, low crosstalk, wide bandwidth, excellent power uniformity, polarization-insensitive property, and compact size. Experimental results reveal that the insertion loss, crosstalk, and power uniformity of the fabricated device at 1550 nm are 0.57, -19.67, and 0.094 dB in the case of TE polarization, while in the TM polarization, the relevant insertion loss, crosstalk, and power uniformity are 0.57, -19.40, and 0.11 dB. Within a wavelength range from 1520 to 1600 nm, for the fabricated device working at TE polarization, the insertion loss, crosstalk, and power uniformity are lower than 1.39, -17.64, and 0.14 dB. In the case of TM polarization, we achieved an insertion loss, crosstalk, and power uniformity less than 1.23, -17.62, and 0.14 dB.
Optical Multi-Mode Interference Power Splitter in GaAs Fabricated by Preferential Etching

MA Hui-lian,YANG Jian-yi,LI Jin,WANG Ming-hua

DOI: https://doi.org/10.3969/j.issn.1005-8788.2000.05.010

2000-01-01

Abstract:A multi-mode interference (MMI) GaAs 1×4 optical p ower splitter that can be directly coupled with single mode fiber array was fabr icated through optimized structure design and preferential etching. The 1.3 μm He-Ne laser measurement indicated that the device has basically realized the re quirement of uniform power splitting, the power imbalance is 0.155 dB.
Co-planar arbitrary ratio optical power splitter based on cascaded hybrid-core vertical directional couplers for arbitrary guide modes

Quandong Huang,Jiali Zhang,Kedi Peng,Jiaqi Ran,Zhaoqiang Zheng,Zhanxiong Qiu,Qiyang Zhang,Meifei Chen,Qingming Chen,Xinyu Zhou,Ou Xu

DOI: https://doi.org/10.1016/j.optlastec.2024.110590

IF: 4.939

2024-01-25

Optics & Laser Technology

Abstract:We propose a co-planar optical power splitter based on cascaded hybrid-core vertical directional couplers, which serves to split arbitrary ratio power of arbitrary guide modes. We fabricate the optical power splitter using micro-fabrication facilities. Our fabricated chip demonstrates power splitting for the E 11 , E 21 and E 12 modes between two few-mode waveguides. The experimental device shows that optical power splitting ranges can be larger than 11.0 dB, 12.1 dB and 11.3 dB for the E 11 , E 21 and E 12 modes, respectively, over the C + L band and beyond. The proposed optical power splitter could be used in the mode division-multiplexing systems where power splitting for arbitrary guide modes in few-mode waveguide is required in the ultra-broadband wavelength range for mode manipulating, such as mode power distribution, mode dependent loss equalization and all-optical MIMO signal processes.

optics,physics, applied
Compact, Broadband, and Low-Loss Silicon Photonic Arbitrary Ratio Power Splitter Using Adiabatic Taper.

Junbo Zhu,Qiu Chao,Haiyang Huang,Yingxuan Zhao,Yang Li,Lue Tao,Xiaojuan She,Han Liao,Rui Huang,Zijian Zhu,Xiang Liu,Zhen Sheng,Fuwan Gan

DOI: https://doi.org/10.1364/ao.413949

IF: 1.9

2020-01-01

Applied Optics

Abstract:The arbitrary ratio power splitter is widely used in photonic integrated circuits (PICs), for signal monitoring, power equalization, signal feedback, and so on. Here we designed a fabrication-tolerant, compact, broadband, and low-loss arbitrary ratio power splitter. The proposed arbitrary ratio power splitter was realized with an adiabatically tapered silicon rib waveguide with 70 nm shallow etches and an Si3N4 waveguide. The fabrication analysis confirmed that both of them are robust to fabrication errors. 3D finite-difference time-domain simulations show a very low excess loss (less than 0.02 dB for Si3N4 waveguide and 0.05 dB for Si rib waveguide), and a broadband operating wavelength range (100 nm). Good fabrication tolerance and standard critical dimensions make the arbitrary ratio power splitter compatible with the standard fabrication process of commercial silicon photonic foundries.
Inverse Design of an Ultra-Compact 3 Db Splitter for Four Modes with Dual Polarizations

Hongzhi Jin,Zhongqiu Zhong,Yingjie Liu,Ke Xu

DOI: https://doi.org/10.1364/oecc.2021.js3e.18

2021-01-01

Abstract:An ultra-compact power splitter for TE0, TE1, TM0 and TM1 modes with a footprint of 6 × 5.25 μm2 is designed. The insertion loss is < 1 dB, and the crosstalk is < -15 dB.
Design and Fabrication of Polymeric Multimode Power Splitter with Secondary Asymmetric Branches

Shu Li,Qiao Lin,Liuhua Chen,Xingkun Wu

DOI: https://doi.org/10.3788/col201109.081302

IF: 2.56

2011-01-01

Chinese Optics Letters

Abstract:A novel design of multimode light power splitter is proposed and fabricated by using secondary asymmetric Y branches. An almost equally divided output among output terminals is obtained experimentally. Mask less laser direct writing technique is applied in the fabrication process to facilitate the formation of power splitters by ultraviolet curable polymer. The analysis of the performances of both four-port and eight-port devices shows that these two dividers obtain a power splitting uniformity of more than 95%.
Low-loss Arbitrary-ratio 1×N Power Splitter

Ping Xue,Zhixin Wang,Che Zhao,Te Chen,Weiwei Hu

DOI: https://doi.org/10.1364/cleo_at.2017.jw2a.136

2017-01-01

Abstract:An arbitrary-ratio 1 ×N power splitter is demonstrated. The power distribution of N-way outputs can be freely customized based on demand. It also has the features of low loss, compact size, easy configuration and wide band.
Broadband and Low-Crosstalk Polarization Splitter-Rotator with Optimized Tapers

Defen Guo,Tao Chu

DOI: https://doi.org/10.1364/osac.1.000841

2018-01-01

OSA Continuum

Abstract:We proposed and experimentally demonstrated high-performance 1550- and 1310-nm silicon polarization splitter-rotators (PSRs) with optimized tapers. Each PSR consists of a particle swarm optimization (PSO)-based bi-level taper and shortcuts to an adiabaticity (STA)-based ridge-waveguide coupler. Ridge waveguides are introduced to increase the coupling coefficient of the STA-based coupler. The measured polarization conversion loss and polarization crosstalk are less than 0.74 and -20 dB, respectively, in the wavelength range of 1500-1600 nm for the 1550-nm PSR, and less than 1 and -23 dB, respectively, in the wavelength range of 1260-1340 nm for the 1310-nm PSR. (C) 2018 Optical Society of America under the terms of the OSA Open Access Publishing Agreement

Dual-mode Arbitrary-Ratio Power Splitter Based on a T-branch Embedded with Nanoholes

Dual-mode arbitrary-ratio power splitter based on a T-branch embedded with nanoholes

Broadband and High Uniformity Y Junction Optical Beam Splitter with Multimode Tapered Branch

T-Branch Waveguide Mirror for Multimode Optical Splitter With Arbitrary Power Ratios

Mid-Infrared, Ultra-Broadband, Low-Loss, Compact Arbitrary Power Splitter Based on Adiabatic Mode Evolution

Ultra-broadband Dual-Mode 3 Db Power Splitter Based on a Y-junction Assisted with Mode Converters.

Arbitrary-Ratio Power Splitters Using Area Modulation Multimode Interference Couplers

Ultra-broadband On-Chip Multimode Power Splitter with an Arbitrary Splitting Ratio

Broadband Multimode 3 Db Optical Power Splitter Using Tapered Couplers.

Ultra Compact and Low Loss Multimode Interferenc Splitter for Arbitrary Power Splitting

Broadband Arbitrary Ratio Power Splitters Based on Directional Couplers with Subwavelength Structure

A novel polarization and dichroic dual-functional splitter with ultra-high splitting ratios

Ultra-broadband Dual-Polarization and Arbitrary Ratio Power Splitters Based on Bezier Curve Optimized Multimode Interference.

Ultra-compact and Broadband Polarization-Insensitive Mode-Order Converting Power Splitter

Optical Multi-Mode Interference Power Splitter in GaAs Fabricated by Preferential Etching

Co-planar arbitrary ratio optical power splitter based on cascaded hybrid-core vertical directional couplers for arbitrary guide modes

Compact, Broadband, and Low-Loss Silicon Photonic Arbitrary Ratio Power Splitter Using Adiabatic Taper.

Inverse Design of an Ultra-Compact 3 Db Splitter for Four Modes with Dual Polarizations

Design and Fabrication of Polymeric Multimode Power Splitter with Secondary Asymmetric Branches

Low-loss Arbitrary-ratio 1×N Power Splitter

Broadband and Low-Crosstalk Polarization Splitter-Rotator with Optimized Tapers