Abstract:By using the capacitive measurement principle, high-performance micromechanical accelerometers provide low noise and power consumption, cost efficiency, and reliability. Capacitive sensors based on changes in the gap between the electrodes, as a rule, require closed-loop control, which increases the level of complexity of the measurement circuit and increases power consumption. Capacitive sensitive elements with a change in the electrode overlap area have a good linearity of the capacitance versus displacement and a large measurement range, but they are more difficult to manufacture. This paper presents and investigates a model of a sensitive element of a sandwich design of a capacitive micromechanical accelerometer, the functioning of which is based on the use of a change in the relative dielectric constant of the dielectric of capacitors due to the introduction of a movable inertial mass between the electrodes of the capacitors, moving under the action of acceleration. As a result, there is a change in capacitance in the output measuring circuit. It is shown that the considered model is sensitive to acceleration and resistant to temperature changes, with low residual mechanical stress in the sensitive element. The modeling and calculations are performed using the Ansys and SolidWorks software. It is found that the movement of the moving mass along the axis of sensitivity X is more than five times the movement of the moving mass along the nonworking axes, and the change in the capacitance between the electrodes along the axis X is almost 2500 times more than the changes in capacitance between electrodes along the nonworking axes Z and Y . Calculations have shown that for all values of the acting acceleration (up to 30 g), the mechanical stress in the sensitive element is much less than the ultimate strength of silicon, equal to 440 MPa. It is found that variation of the temperature from –40 to 85°C leads to minor changes in capacitance along the working axis (0.0025–0.003 pF). This indicates the temperature stability of the investigated micromechanical accelerometer sensing element. The results of the analysis show that the developed and investigated model of the sensitive element of the sandwich design ensures the sensitivity of the micromechanical accelerometer and the stability of its parameters.

Design, Modelling and Characterization of Comb Drive MEMS Gap-Changeable Differential Capacitive Accelerometer

Mechanical Design Optimization of A Single-Axis Moems Accelerometer Based on A Grating Interferometry Cavity for Ultrahigh Sensitivity

Design of Force-Balance Capacitive Accelerometer

A Stiffness-Tunable MEMS Accelerometer

Study of a Novel Micromachined Capacitive Accelerometer

A Micromachined Silicon-on-Glass Accelerometer with an Optimized Comb Finger Gap Arrangement

A Novel Cmos Out-Of-Plane Accelerometer with Fully Differential Gap-Closing Capacitance Sensing Electrodes

Design, Modelling, and Simulation analysis of a Single Axis MEMS-based Capacitive Accelerometer

Design and Application of a Metal Wet-Etching Post-Process for the Improvement of CMOS-MEMS Capacitive Sensors

Modeling the Sensitive Element of the Sandwich Construction of a Capacitive Micromechanical Accelerometer, Taking into Account the Change in the Dielectric Constant

Implementation of A Gap-Closing Differential Capacitive Sensing Z-Axis Accelerometer on an Soi Wafer

An alternative capacitive transducer design for sensitivity enhancement in MEMS Lorentz force magnetometers

Design, Modeling and Analysis of Highly Reliable Capacitive Microaccelerometer Based on Circular Stepped-Plate and Small-Area Touch Mode

The High-Efficiency Design Method for Capacitive MEMS Accelerometer

Cmos Interface Circuitry For A Closed-Loop Capacitive Mems Accelerometer

Design, Fabrication and Test of a Low Range Capacitive Accelerometer With Anti-Overload Characteristics

Modeling and Analysis of MEMS Capacitive Pressure Sensors with Vertical Comb Fingers

Design of a High-Resolution Capacitive Microaccelerometer

A Novel Tunable Lateral Sensing Capacitive Silicon Micromachined Accelerometer with High Sensitivity

A new structure and modeling of a three-axis MEMS capacitive accelerometer with high dynamic range and sensitivity

Design Of Readout Circuits Used For Micro-Machined Capacitive Accelerometer