Abstract:A novel approach is developed by incorporating buried selenium seed layers to enhance the performance of Sb2Se3 solar cells through improved heterojunction quality and reduced defect density. This method significantly boosts both VOC and PCE, reaching 498.3 mV and 8.42%, respectively, marking the highest efficiency reported for Sb2Se3 solar cells prepared via VTD. Quasi‐1D antimony selenide (Sb2Se3) is known for its stable phase structure and excellent light absorption coefficient, making it a promising material for high‐efficiency light harvesting. However, the (Sb4Se6)n ribbons align horizontally, increasing defect interference and limiting vertical carrier transport. Herein, a novel strategy of burying selenium (Se) seed layers to reduce lattice mismatch at the heterojunction interface, promote crystal orientation, mitigate deep donor defects, increase P‐type carrier concentration, and purify the PN junction, is proposed. Admittance spectroscopy reveals that Sb2Se3 solar cells with Se seed layers have higher activation energies for defect states and significantly lower defect densities (1.2 × 1014, 2.7 × 1014, and 1.3 × 1015 cm−3 for D1, D2, and D3) compared to an order of magnitude higher densities in Sb2Se3 solar cells without a Se seed layer. First‐principles calculations support these findings, showing that Se seed layers create a Se‐rich environment, reducing selenium vacancies (VSe), antimony on selenium sites (SbSe), and interface defects. This dual passivation mechanism suppresses defect formation and activation, increasing carrier concentration and open‐circuit voltage (VOC). Ultimately, employing this novel method, a VOC of 498.3 mV and an efficiency of 8.42%, the highest performance reported for Sb2Se3 solar cells prepared via vapor transport deposition (VTD), are achieved.

Intrinsic Defect Limit to the Electrical Conductivity and a Two-Step p-Type Doping Strategy for Overcoming the Efficiency Bottleneck of Sb2S3-Based Solar Cells

Extrinsic Dopants in Quasi-One-dimensional Photovoltaic Semiconductor Sb2S3: A First-Principles Study

Influence of defects and dopants on the photovoltaic performance of Bi2S3: First-principles insights

n-Type Doping of Sb2S3 Light-Harvesting Films Enabling High-Efficiency Planar Heterojunction Solar Cells.

p‐Type Antimony Selenide via Lead Doping

A Codoping Strategy for Efficient Planar Heterojunction Sb2S3 Solar Cells

Interface Defects Passivation and Conductivity Improvement in Planar Perovskite Solar Cells Using Na2S Doped Compact-TiO2 Electron Transport Layers.

Enhanced Sb2Se3 Solar Cell Performance Through Theory-Guided Defect Control

Upper efficiency limit of Sb2Se3 solar cells

Heterojunction Lithiation Engineering and Diffusion-Induced Defects Passivation for Highly Efficient Sb2(S,Se)3 Solar Cells

Innovative In Situ Passivation Strategy for High‐Efficiency Sb2(S,Se)3 Solar Cells

Oxygen‐Assisted Tailoring of Evaporated PbS Hole Transport Layer for Highly Efficient Antimony Sulfide Solar Cells

Manipulating the Intrinsic Defect of MnS by Surface Sulfidation for Inverted Sb2(S,Se)3 Planar‐Heterojunction Solar Cells

Deep defects limiting the conversion efficiency in Sb2Se3 thin-film solar cells

Molecular Beam Epitaxy Deposition of In Situ O‐Doped CdS Films for Highly Efficient Sb2(S,Se)3 Solar Cells

Doping Effects in SnO2 Transport Material for High Performance Planar Perovskite Solar Cells

Mechanism of Defect Passivation in Sb2Se3 Solar Cells via Buried Selenium Seed Layer

Efficiency improvement for post-sulfurized CIGS solar cells enabled by in situ Na doping

An effective engineering with simultaneous carrier density enhancement and interface optimization enables efficient Sb2Se3 solar cells

Enhanced charge carrier transport via efficient grain conduction mode for Sb2Se3 solar cell applications

Towards high efficiency inverted Sb2Se3 thin film solar cells