Abstract:In this work, thioacetamide (TA) is selected as a sulfur‐containing additive for the precursor solution used in the hydrothermal deposition of Sb2(S,Se)3. With the incorporation of TA, the formation of large voids within the Sb2(S,Se)3 absorber is suppressed, and deep‐level donor‐like defects such as sulfur vacancies are passivated, resulting in enhanced performance of Sb2(S,Se)3 solar cells. Antimony selenosulfide (Sb2(S,Se)3) has recently emerged as a promising light‐absorbing material, attributed to its tunable photovoltaic properties, low toxicity, and robust environmental stability. However, despite these advantages, the current record efficiency for Sb2(S,Se)3 solar cells significantly lags behind their Shockley–Queisser limit, especially when compared to other well‐established chalcogenide‐based thin‐film solar cells, such as CdTe and Cu(In,Ga)Se2. This underperformance primarily arises from the formation of unfavorable defects, predominately located at deep energy levels, which act as recombination centers, thereby limiting the potential for performance enhancement in Sb2(S,Se)3 solar cells. Specifically, deep‐level defects, such as sulfur vacancy (VS), have a lower formation energy, leading to severe non‐radiative recombination and compromising device performance. To address this challenge, thioacetamide (TA), a sulfur‐containing additive is introduced, into the precursor solution for the hydrothermal deposition of Sb2(S,Se)3. This results indicate that the incorporation of TA helps in passivating deep‐level defects such as sulfur vacancies and in suppressing the formation of large voids within the Sb2(S,Se)3 absorber. Consequently, Sb2(S,Se)3 solar cells, with reduced carrier recombination and improved film quality, achieved a power conversion efficiency of 9.04%, with notable improvements in open‐circuit voltage and fill factor. This work provides deeper insights into the passivation of deep‐level donor‐like VS defects through the incorporation of a sulfur‐containing additive, highlighting pathways to enhance the photovoltaic performance of Sb2(S,Se)3 solar cells.

Innovative In Situ Passivation Strategy for High‐Efficiency Sb2(S,Se)3 Solar Cells

Defects Passivation via Potassium Iodide Post‐Treatment for Antimony Selenosulfide Solar Cells with Improved Performance

Active Passivation of Anion Vacancies in Antimony Selenide Film for Efficient Solar Cells

Back Contact Passivation of Sb2se3 Solar Cells Via Antimony Trichloride Solution

Regulating Energy Band Alignment Via Alkaline Metal Fluoride Assisted Solution Post‐Treatment Enabling Sb2(S,Se)3 Solar Cells with 10.7% Efficiency

Regulating Energy Band Alignment via Alkaline Metal Fluoride Assisted Solution Post‐Treatment Enabling Sb 2 (S,Se) 3 Solar Cells with 10.7% Efficiency

Mechanism of Defect Passivation in Sb2Se3 Solar Cells via Buried Selenium Seed Layer

Light-Absorber Engineering Induced Defect Passivation for Efficient Antimony Triselenide Solar Cells

Fabricating High‐Efficiency Sb2(S,Se)3 Solar Cells by Novel Additive‐Assisted Longitudinal Component Engineering

Heterojunction Lithiation Engineering and Diffusion-Induced Defects Passivation for Highly Efficient Sb2(S,Se)3 Solar Cells

Additive‐Assisted Hydrothermal Growth Enabling Defect Passivation and Void Remedy in Antimony Selenosulfide Solar Cells

Heterojunction Lithiation Engineering and Diffusion-Induced Defect Passivation for Highly Efficient Sb2(S,Se)3 Solar Cells

Crystal Growth Promotion and Defect Passivation by Hydrothermal and Selenized Deposition for Substrate-Structured Antimony Selenosulfide Solar Cells

Defects Passivation and Crystal Growth Promotion by Solution-Processed K Doping Strategy Toward 16.02% Efficiency Cu(In,Ga)(S,Se) <sub>2</sub> Solar Cells

Bulk Defect Passivation for Full‐Inorganic Sb2S3 Solar Cells by Sulfur‐Atmosphere Recrystallization Process

Suppressing Buried Interface Nonradiative Recombination Losses Towards High‐efficiency Antimony Triselenide Solar Cells

A Robust Hydrothermal Sulfuration Strategy toward Effective Defect Passivation Enabling 6.92% Efficiency Sb<sub>2</sub>S<sub>3</sub> Solar Cells

Regulating Deposition Kinetics via A Novel Additive-assisted Chemical Bath Deposition Technology Enables 10.57%-efficient Sb2Se3 Solar Cells

Regulating Energy Band Alignment via Alkaline Metal Fluoride Assisted Solution Post‐Treatment Enabling Sb <sub>2</sub> (S,Se) <sub>3</sub> Solar Cells with 10.7% Efficiency

Crystal Reconstruction and Defect Healing Enabled High-Quality Sb2Se3 Films for Solar Cell Applications

Confined‐space selenium assisted tellurization post‐treatment strategy for efficient full‐inorganic Sb2S3 thin film solar cells