Abstract:TiAl-based alloys have recently received considerable attention as one of the promising candidates for application in aero engine blades by replacing the Ni-based superalloys because of their unique properties, such as high specific strength, high specific stiffness and good oxidation resistance. However, there are some shortcomings limiting the application of TiAl-based alloys, namely, their brittleness and poor processing properties. Nevertheless, aero engine blades usually suffer a variety of cyclic loadings during the period of services, which finally results in fatigue failure. According to statistics, fatigue failure, mainly high cycle fatigue (HCF), occupies almost 80% failure modes of gas turbine blades in aero engines. Consequently, more and more researches about fatigue behavior of blade materials have been done in the last tens of years. However, there are less relevant results about TiAl-based alloys, especially HCF properties. Recently, the advancement of directional solidification (DS) of TiAl-based alloys using cold crucible has revealed that the ductility can be enhanced at room and elevated temperature. For purpose to verify the influence of DS structures on the tensile and HCF properties, TiAl-based alloy in composition with Ti-47Al-2Cr-2Nb (atomic fraction, %) was prepared and evaluated in this work. Directionally solidified Ti-47Al-2Cr-2Nb alloy ingots with different withdrawal rates (1.0, 1.2 and 1.4 mm/min) were prepared by cold crucible method under alter electromagnetic field in a vacuum furnace. Based on these ingots, macro and microstructures have been characterized by methods of digital camera, OM, SEM and XRD. Furthermore, the tensile properties at room and high temperature (800 degrees C) as well as HCF properties at room temperature have been measured respectively. So, the relationship between microstructures and mechanical properties of TiAl-based alloy, especially HCF properties, was demonstrated reasonably and mechanism in which HCF cracks propagated was discussed. The results show that the comprehensive mechanical properties of Ti-47Al-2Cr-2Nb alloy can be significantly improved after directionally solidified using cold crucible. The tensile strength reaches 652 MPa at room temperature with the maximum elongation of 1.5%. Meanwhile, the tensile strength at 800 degrees C attains 490 MPa with the elongation of 5.0%. Based on the data of HCF test at room temperature with the stress ratio of 0.1, the equations of stress amplitude-number of cycles to failure (S-N) curve at different withdrawal rates are calculated. The fatigue limits are 300 and 247 MPa with the withdrawal rates of 1.0 and 1.2 mm/min, respectively, namely, with the increase of withdrawal rate, the fatigue fracture resistance decreases. The mode of HCF fracture of directionally solidified Ti-47Al-2Cr-2Nb alloy behaves in brittle cleavage fracture. And micro-cracks which can propagate along and perpendicular to the lamellae at the same time are observed between alpha(2)/gamma lamellae and around B-2 phases.

Effect of Thermal Cycling on Microstructure and Fatigue Properties of Ti-6Al-4V Alloy

A Study of the Back Stress and the Friction Stress Behaviors of Ti-6Al-4V Alloy During Low Cycle Fatigue at Room Temperature

Effect of cyclic straining at elevated-temperature on static mechanical properties, microstructures and fracture behavior of nickel-based superalloy GH4145/SQ

Thermal cycling behavior of as-quenched and aged Ti-6Al-4V alloy

Microstructural effects on the high-cycle fatigue and fracture behaviors of Ti-6Al-4V alloy

Effect of Microstructure on Ultra-High Cycle Fatigue Behavior of Ti–6Al–4V

Effects of Thermal Cycling on Tensile Properties of Ti-6Al-4V Alloy at Room and Cryogenic Temperatures

Effects of cycle heat treatment on the microstructure and mechanical property of as-cast ?-TiAl alloy

Effect of Heat Treatment on Very High Cycle Fatigue Properties of TC4

Microstructure stability and damage mechanisms in an α/β Ti-6Al-4V-0.55Fe alloy during low cycle dwell-fatigue at room temperature

Thermal Stability and Lattice Strain Evolution of High‐Nb‐Containing TiAl Alloy under Low‐Cycle‐Fatigue Loading

High-temperature Fatigue Property of Ti46Al8Nb Alloy with the Fully Lamellar Microstructure

Ultra-High Cycle Fatigue Behavior of Ti-6al-4v Alloy

Effect of thermal exposure on the microstructure and mechanical properties of Ti60 alloy

Effect of Microstructure on High Cycle Fatigue Behavior of Al-Li Binary Alloy

Effect of Cyclic Heat Treatment on Microstructures and Mechanical Properties of Directionally Solidified Ti–46Al–6Nb Alloy

Microstructure evolution and cyclic deformation behavior of Ti-6Al-4 V alloy via electron beam melting during low cycle fatigue

The effect of multiple thermal cycles on Ti-6Al-4V deposits fabricated by wire-arc directed energy deposition: Microstructure evolution, mechanical properties, and corrosion resistance

The Microstructure and High Cycle Fatigue Performance of As-Cast and Directionally Solidified Ti46Al7Nb Alloy under the Three-Point Bending Loading

TENSILE AND HIGH CYCLE FATIGUE PROPERTIES OF Ti-47Al-2Cr-2Nb DIRECTIONALLY SOLIDIFIED BY COLD CRUCIBLE METHOD

Effect of Thermal Cold Cycling on the Microstructure and Properties of Al–Cu–Mg–Ag Alloy