Abstract:Objectives: This study aims to investigate bond strength between zirconia and resin cement through surface treatments with Er: YAG laser, Nd: YAG laser, and Si-Zr coating. Methods: Seventy-five round pre-sintered zirconia discs with a diameter of 18 mm and a thickness of 1.5 mm were prepared by a powder compactor. Fifty discs were randomly divided into five groups of 10 discs each and were subjected to five surface treatments: no treatment (control group), sandblasting with alumina particles (sandblasting group), Er: YAG laser treatment (Er: YAG laser group), Nd:YAG laser treatment (Nd: YAG laser group), and Si-Zr coating treatment (Si-Zr coating group). The discs were then bonded to composite resin columns with resin cement. The shear bond strength of each group was tested with a universal tester. Roughness tester, scanning electron microscope (SEM), and energy dispersive spectroscopy were used to analyze surface performance. Results: The bond strength of the Si-Zr coating group was higher than that of the remaining groups (P<0.05). The difference in bond strength between the sandblasting group and the Er: YAG laser group was not statistically significant (P>0.05), but both of them had higher bond strength than the Nd: YAG laser group (P<0.05). The Si-Zr coating group had the highest surface roughness (P<0.05). The surface roughness of the sandblasting, Er: YAG laser, and Nd: YAG laser groups was higher than that of the control group (P<0.05), but the difference among the three groups was not statistically significant (P>0.05). SEM observations showed irregular scratches on the surface of the sandblasting group and large pits with holes on the surface of the Er: YAG and Nd: YAG laser groups. In the Er: YAG laser group, the crystal structure was replaced by a smooth surface with a large amount of microcracks due to partial melting. Complex porous structures that comprised "island-like" structures and mass pores among the grains were observed on the surface of the Si-Zr coating. Only Zr, O, and Y were detected on the surfaces of the control, Er: YAG laser, and Nd: YAG laser groups. Al was found on the surface of the sandblasted group, and a higher proportion of Si was detected on the surface of the Si-Zr coating group. Conclusions: Er: YAG laser and Nd: YAG laser treatment on the zirconia ceramic surface could increase roughness and improve the bond strength to resin cement. Si-Zr coating treatment is an effective alternative for increasing the roughness and bond strength of zirconia surface and is superior to sandblasting and laser treatments.

Influence of Zirconia Sol-Gel Coating on Fracture Strength of Chemical Strengthened Soda Lime Glass

Activating Continuous Dislocation Pinning Enhanced Toughness of Nanocomposite Coating Through Specially Oriented Semicoherent Heterointerface Lattice Distortion

Mechanical and Optical Properties of Ion-exchange Strengthened Glass Coated with Sol-Gel Derived ZrO2-SiO2 Film

Effect of Silica Coating on Fracture Strength of Glass-Infiltrated Alumina Ceramic Cemented to Dentin.

Effects of Residual Stresses on Strength and Crack Resistance in ZrO2 Ceramics with Alumina Coating

Chemical strengthening of high aluminosilicate glasses and experimental fitting

Strengthen the bonding of self-glazed zirconia to enamel by sol–gel coating

The Competing Effect of Initial Crack Depth Versus Chemical Strengthening Parameters on Apparent Fracture Toughness of Sodium Aluminosilicate Glass

Effect of laser and coating surface treatment on the bond strength of zirconia ceramics

The effect of surface treatment and low-temperature degradation on flexural strength of additive manufactured zirconia

Investigation on Mircro-Structure of Zircon Coating

[Effect of SiO2-ZrO2 slurry coating on shear bond strength of zirconia to resin cement]

Influence of Zirconia and Organic Additives on Mechanical and Electrochemical Properties of Silica Sol-Gel Coatings

Fractography of Self-Glazed Zirconia with Improved Reliability

Surface damage resistance and yielding of chemically strengthened silicate glasses: From normal indentation to scratch loading

A Novel Porous Silica-Zirconia Coating for Improving Bond Performance of Dental Zirconia

Enhancing the design bending strength of new and aged glass with a functional coating

Flexural strength of novel glass infiltrated monochrome and multilayer high yttrium oxide containing zirconia upon various sintered cooling rates

Crystallization of ZABS glass and its wettability on diamond abrasive

Effect of ZrO(2) additions on the crystallization, mechanical and biological properties of MgO-CaO-SiO(2)-P(2)O(5)-CaF(2) bioactive glass-ceramics

Borosilicate glass as a surface finishing alternative for improving the mechanical properties of third-generation zirconia