Abstract:In this work, the role of Al addition in modifying the microstructure and mechanical properties of the Mg-1.0Ca-xAl (x = 0.6, 1.0 wt%; termed as XA10 and XA11, respectively) based alloys has been systematically investigated. Microstructural examination showed that, when the Al content is low, the Al and Ca atoms were inclined to segregate to the dislocation lines in the XA10 sample. As a result, the mobility of dislocation was restrained and the dynamic recovery behavior was hindered, which leads to a low degree of dynamic recrystallization. When the Al content is high, in contrast, no apparent Ca/Al segregations along dislocations have been found in XA11-0 extrusion billet during the whole stages of processing, which results in the enhanced dislocation mobility. Consequently, the recovery of dislocations and dynamic recrystallization rate can be largely enhanced at the earlier stage of extrusion. More importantly, subsequently formed high density Guinier-Preston (G.P.) zones and nano-disk Al2Ca phases in the high-Al content Mg sample can play an effective role in inhibiting the growth of subgrains and dynamically recrystallized (DRXed) grains, which enhance the thermal stability of high density low angular grain boundaries (LAGBs) in the later extrusion stage. The high density nano-disk phases, high volume fraction of DRXed grains, as well as the high density LAGBs in the un-DRXed grains, can together contribute to both high strength and good elongation of the XA11 sample. The findings lead to the controllable Mg-Ca based alloy designing strategy that can improve the strength and ductility simultaneously.

Preparation of CaAl12O19/(MgAl2O4-Al2O3) Functional Gradient Materials

Novel Calcium Hexaluminate/spinel-Alumina Composites with Graded Microstructures and Mechanical Properties

Influence of molar ratio of CaO and γ-Al2O3 on synthesis of lamellar calcium hexaluminate

Influence of molar ratio of CaO and γ-Al_2O_3 on synthesis of lamellar calcium hexaluminate

Study on Synthesis of CA6 and MgAl2O4 with Dolomite As a Source of Calcium and Magnesium

Preparation of Calcium Hexaluminate Using Al<sub>2</sub>O<sub>3 </sub>and White Beach Sand from Western Australia <sub> </sub>

Preparation of Calcium Hexaluminate Using Al2o3 and White Beach Sand from Western Australia

Preparation of Zr4+ Doped Calcium Hexaaluminate with Improved Slag Penetration Resistance

FABRICATION AND PROPERTIES OF CALCIUM-HEXALUMINATE/MAGNESIUM-ALUMINIUM SPINEL COMPOSITES

Synthesis of Functionally Graded AA7075-B4C Composite with Multi-Level Gradient Structure

Preparation and properties of MgAl 2O 4-CaAl 12O 19 high temperature composite

Preparation and characterization of LnMgAl11O19 (Ln=La, Nd, Gd) ceramic powders

Preparation and Properties of MgAl<sub>2</sub>O<sub>4</sub>-CaAl<sub>12</sub>O<sub>19</sub> High Temperature Composite

Preparation of Zr 4+ doped calcium hexaaluminate with improved slag penetration resistance

In-situ synthesis of porous calcium hexa-aluminate ceramics and growth mechanism of the plate-like grains

Preparation of platelet CaMg2Al16O27 (CM2A8) grains via adjusting MgO and Al2O3 contents

In-situAl/Mg2Si Functional Graded Materials (fgms) Prepared by Electromagnetic Separation

Role of Al addition in modifying microstructure and mechanical properties of Mg-1.0 wt% Ca based alloys

In-Situ Al/24si Functional Graded Materials Prepared by Electromagnetic Separation

Fabrication and Properties of CaAl12O19-Al2O3 Composite Ceramics

A New Approach for the Preparation of Functionally Graded Materials Via Slip Casting in a Gradient Magnetic Field