Abstract:In this work, the role of Al addition in modifying the microstructure and mechanical properties of the Mg-1.0Ca-xAl (x = 0.6, 1.0 wt%; termed as XA10 and XA11, respectively) based alloys has been systematically investigated. Microstructural examination showed that, when the Al content is low, the Al and Ca atoms were inclined to segregate to the dislocation lines in the XA10 sample. As a result, the mobility of dislocation was restrained and the dynamic recovery behavior was hindered, which leads to a low degree of dynamic recrystallization. When the Al content is high, in contrast, no apparent Ca/Al segregations along dislocations have been found in XA11-0 extrusion billet during the whole stages of processing, which results in the enhanced dislocation mobility. Consequently, the recovery of dislocations and dynamic recrystallization rate can be largely enhanced at the earlier stage of extrusion. More importantly, subsequently formed high density Guinier-Preston (G.P.) zones and nano-disk Al2Ca phases in the high-Al content Mg sample can play an effective role in inhibiting the growth of subgrains and dynamically recrystallized (DRXed) grains, which enhance the thermal stability of high density low angular grain boundaries (LAGBs) in the later extrusion stage. The high density nano-disk phases, high volume fraction of DRXed grains, as well as the high density LAGBs in the un-DRXed grains, can together contribute to both high strength and good elongation of the XA11 sample. The findings lead to the controllable Mg-Ca based alloy designing strategy that can improve the strength and ductility simultaneously.

Preparation of platelet CaMg2Al16O27 (CM2A8) grains via adjusting MgO and Al2O3 contents

Morphology-controlled Synthesis of Α-Alumina Microplatelets Through an Additive-Assisted Molten Salt Reaction

Novel temperature dependent process for α-Al2O3 platelets

Role of Al addition in modifying microstructure and mechanical properties of Mg-1.0 wt% Ca based alloys

Synthesis of thin alpha alumina platelets with a large aspect ratio

Influence of Ca Content on Microstructure and Mechanical Properties of Extruded Mg–Al–Ca–Mn Alloys

Influence of chemical composition on the room temperature plas-ticity of C15 Ca-Al-Mg Laves phases

Strengthening of Mg-Al-Ca alloys with C15 and C36 Laves phases

Mg adsorption on MgAl2O4 surfaces and the effect of additive Ca: A combined experimental and theoretical study

Tailoring the mechanical properties of Al4Ca intermetallic by doping M (M = Cu, Zn, Mg, Fe and Mn) from DFT calculations

Characterization of crystal structure and precipitation crystallography of a new MgxAl2-xGd phase in Mg97Al1Gd2 alloy

Influence of Mg Doping on the Structure and Mechanical Properties of Al2Cu Precipitated Phase by First-Principles Calculations

Effect of Ca Concentration on Microstructure and Mechanical Properties of As-Cast and As-Extruded Quasicrystal-Strengthened Mg-7.2Zn-2.4Gd Alloy

Influence of Mg content on ageing precipitation behavior of Al-Cu-Li-x alloys

Effect of Al on the Microstructure and Mechanical Properties of Mg–Sn–Ca–Mn Wrought Alloy

Evolution of Deformation Substructure and MgxZnyCaz Metastable Phase in Fine-Grained Mg Alloys

Microstructure, anticorrosion, biocompatibility and antibacterial activities of extruded Mg−Zn−Mn strengthened with Ca

Aluminium Induced Sub-Microsized <i>α</i>-Al<sub>2</sub>O<sub>3</sub> Platelets in the Soda-Lime-Silica Glass

Insights into precipitation characteristics and strengthening mechanisms in a low Cu/Mg ratio Al-Cu-Mg-Ag alloy

Effects of calcium glycerophosphate concentration on micro-arc oxidation coating of Mg alloy