Abstract:In the present work, the feasibility and effectiveness of fabricating La2O3-doped W-based bulk using W-based composite powders of core-shell structure with W particle as a core and La(OH)3 as a shell, without hydrogen reduction treatment, was evaluated. La(OH)3 was first coated on the surface of pure W (uncoated) powders at a weight percentage of 3.50% to prepare composite (coated) powders using the electroless plating method. The uncoated and coated powders without being treated by hydrogen reduction were then sintered using spark plasma sintering (SPS) to fabricate bulks. The results showed that the core-shell structure with W particle as a core and La(OH)3 film as a shell was fabricated. La2O3-doped W-based bulk with about 2.93 wt.% La2O3 was obtained because of the transformation from La(OH)3 to La2O3. The La2O3 particles with larger sizes were distributed mainly at W grain boundaries and those with smaller sizes were distributed mainly inside W grains. The major densification mechanism of the sintered bulk from coated powders was the filling effect of La2O3 particles on the pores as compared with the sintered bulk from uncoated powders, which could be evaluated by using a two-ball sintering neck model. The relative content of O in the form of WO3 in the sintered bulk from coated powders was identical to that in the sintered bulk from uncoated powders. The W grain size of the sintered bulk from coated powders was smaller than that of the sintered bulk from uncoated powders. The thermal properties, mechanical properties, and irradiation properties of the sintered bulk from coated powders were all higher than those of the sintered bulk from uncoated powders. With the increase of sintering temperature, the evolution of the coated powders in the initial sintering period could be divided into six stages that were not completely independent and occurred in approximate sequence from the perspective of simplification. It was feasible and effective to fabricate La2O3-doped W-based bulk using the precursor W-based composite powders of core-shell structure with W particle as a core and La(OH)3 as a shell without being treated by hydrogen reduction.

Microstructure Analysis of a W-1%La2O3 Alloy

Microstructure and performance of rare earth element-strengthened plasma-facing tungsten material

The W alloying effect on thermal stability and hardening of nanostructured Cu-W alloyed thin films

Microstructural Effects of Y2O3 and TiC Additions in Tungsten

Phase Analysis of Nano-Sized Particles in As-Forged W-1%La2o3 Alloy

D2 retention and microstructural evolution during He irradiation in candidate plasma facing material W-La2O3 alloy

Microstructure and Properties of La2O3 Doped W Composites Prepared by a Wet Chemical Process

Microstructure and phase stability of TiVTa-based low-activation, multi- principal-element alloys

Surface Cracking of Tungsten-Vanadium Alloys under Transient Heat Loads

Theoretical Predictions of the Structural and Mechanical Properties of Tungsten–Rare Earth Element Alloys

Microstructure and Properties of La2O3-doped Tungsten-Based Bulk Material and Its Densification Mechanism During Spark Plasma Sintering Process

Effects of doping route on microstructure and mechanical properties of W−1.0wt.%La2O3 alloys

Microstructure and Its High Temperature Oxidation Behavior of W-Cr Alloys Prepared by Spark Plasma Sintering

Microstructure and mechanical characterizations of liquid phase sintered W-Ni-Cu heavy alloy modified with La 2 O 3 and Fe addition

Dependence of deuterium retention and surface blistering on deuterium plasma exposure temperature and fluence in lanthanum oxide doped tungsten

Effect of rare earth oxide doping on microstructure and mechanical property of Mo-30 W solid solution alloy

Development of Tungsten As Plasma-Facing Materials by Doping Tantalum Carbide Nanoparticles

Influence of impurity gas seeding into deuterium plasma on the surface modification, sputtering erosion and deuterium retention in W and W-La2O3 alloy

A prospect of using ternary W-5 wt%V-5 wt%Ta alloy manufactured by mechanical alloying and spark plasma sintering as plasma-facing material

An Investigation of the Microstructure and Properties of Rolled W-Al2O3 Alloy

Spark plasma sintering of tungsten-based WTaVCr refractory high entropy alloys for nuclear fusion applications