Abstract:The CoCrFeNiAl high-entropy alloy, with varying Al compositions, was utilized as the bonding phase in this study to fabricate WC-10%CoCrFeNiAl x (where x represents the mole ratio of Al element, ranging from 0 to 1) hard alloys using the Spark Plasma Sintering method. The investigation focused on elucidating the influence mechanism of microstructure and properties of CoCrFeNiAl x high-entropy alloys on the mechanical properties of WC-10%CoCrFeNiAl x hard alloys. Isothermal oxidation testing was subsequently conducted to examine the impact of Al content on the high-temperature oxidation resistance of WC-10%CoCrFeNiAl x hard alloys. Finally, a comparison was made between the mechanical properties and high temperature oxidation resistance of WC-10%CoCrFeNiAl x hard alloys and conventional WC-6Co cemented carbide. The findings suggest that as the Al content increases, the CoCrFeNiAl x high-entropy alloy undergoes a transition from a single Face-Centered Cubic (FCC) phase to a combination of FCC and Body Centered Cubic (BCC) phases, ultimately transforming into a BCC phase. This evolution results in a gradual enhancement in hardness. The mechanical properties of WC-10CoCrFeNi hard alloy exhibit exceptional characteristics when the Al content is eliminated, with hardness, fracture toughness, and bending strength reaching 1702 MPa, 13.0 MPa·m 1/2 , and 1378 MPa respectively. As the Al content increases in WC-10%CoCrFeNiAl x hard alloys, there is a corresponding increase in hardness while fracture toughness and bending strength gradually decrease. Furthermore, an enhancement in high temperature oxidation resistance is observed. Finally, in comparison to the conventional WC-6Co hard alloy, the mechanical properties of WC-10CoCrFeNiAl x hard alloys exhibit similarity while demonstrating a significant enhancement in oxidation resistance.

Microstructure and Its High Temperature Oxidation Behavior of W-Cr Alloys Prepared by Spark Plasma Sintering

Fabrication of nanocrystalline supersaturated W–Al alloys with enhanced thermal stability and high sinterability

Comparative Study of Oxidation Behavior of Cr2O3 Dispersed W-Zr Alloys at 800°C, 1000°C and 1200°C Fabricated Using Powder Metallurgy

Microstructure and high-temperature oxidation behavior of Ti3AlC 2/W composites

High-Temperature Oxidation Properties and Microstructural Evolution of Nanostructure Fe-Cr-Al ODS Alloys

Effect of Cr and W addition on the oxidation behavior of Ni–8%Al alloy at 1000 °C

The W alloying effect on thermal stability and hardening of nanostructured Cu-W alloyed thin films

Effect of Al content in CoCrFeNiAl x HEA on mechanical properties and high temperature oxidation resistance of WC-10%CoCrFeNiAl x hard alloy

High temperature oxidation behavior of a novel Ni-Cr-W-Al-Ti superalloy

Microstructure Evolution and Oxidation Resistance Properties of Oxide Dispersion Strengthened FeCrAl Alloys at 1100 °C

Effect of Cr on Microstructure, Mechanical Properties, and Wear Behavior of in Situ 20 Wt.%al2o3/fe-25Al Composites

High-temperature steam oxidation behavior and failure mechanisms of Al alloyed Cr coatings on Zr-4 alloy

Improvement of high-temperature oxidation resistance of WC–Co–Ni alloy by Cr3C2–CeO2–WS2 mixed additives and its mechanism

High-gravity Combustion Synthesis of W-Cr Alloys with Improved Hardness

Microstructure Evolution and Mechanical Properties of Ultra-Fine Grain AlCrFe2Ni2Wx High-Entropy Alloys

Exploring the high-temperature steam oxidation behaviors of the lean-Cr (7–10 wt%) FeCrAl alloys

Microstructure evolution and high temperature air oxidation behaviour of thick Cr coatings at 1200°C

Non-isothermal Oxidation and Ignition Prediction of Ti-Cr Alloys

The oxidation of micro-crystalline Co–Cr alloys under balanced oxygen pressure of Co2O3/Co powders

Ultrafine-grained W-based alloys prepared by HIP with ultrahigh hardness and excellent thermal stability

The effect of micro-crystallizing on the oxidation resistance of Cu–Cr alloy in air