Abstract:Additively manufactured alloys undergo a rapid solidification process followed by thermal cycles, which promotes the microstructures to return to equilibrium. The microstructural behavior therein is especially complicated and inconceivable at times, thereby greatly restricting the tailorability of microstructures for additive manufacturing. To improve the understanding of microstructure formation in rapidly solidified TiAl alloy, Ti-47Al-2Cr-2Nb powders were aging-treated to reveal the microstructural evolution behavior on multiple scales, and the microstructural transformation mechanisms were comprehensively analyzed from the viewpoints of thermodynamics and kinetics. The results show that the rapidly solidified TiAl alloy almost retains the alpha 2 phase, which then transforms into nanolamellar structures or equiaxed gamma microstructures depending on the temperature. The completely different microstructure selections were determined by the competitive growth of lamellar structures and equiaxed gamma grains. More importantly, atypical pathways for lamellar and twinning transformations were first discovered in these microstructural transformation processes. A 6H-type long periodic stacking ordered (LPSO) phase was observed to be in the form of straight laths in the retained alpha 2 phase, and 9R-and 18R-type LPSO phases were discovered in the equiaxed gamma grains. The 6H-type LPSO phase transformed into nano gamma laths, whose formation driving force was deduced to result from the extremely high elastic energy stored in the retained alpha 2 phase. The 9R-and 18R-type LPSO phases transformed into a more stable gamma twin phase to reduce the entire energy of the system. This research may potentially enhance the understanding of the microstructure of additively manufactured TiAl alloy and consequently, the tunability of such microstructure as required. (c) 2022 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Unusual Ordered Phases With Long Periodic Stacking Structures In An Additively Manufactured Tial Alloy

Investigation on the Microstructure and Mechanical Behaviors of a Laser Formed Nb-Ti-Al Alloy

Alternative-band microstructure and LPSO phase in TiAl alloy produced by direct laser deposition

Atypical Pathways for Lamellar and Twinning Transformations in Rapidly Solidified TiAl Alloy

Anisotropic Tensile Behavior of Ti-47Al-2Cr-2Nb Alloy Fabricated by Direct Laser Deposition

Microstructure characteristics of a γ single-phase Ti-55Al-7.5Nb alloy fabricated via additive manufacturing

Effect of the Morphology of Long-Period Stacking Ordered Phase on Mechanical Properties and Corrosion Behavior of Cast Mg-Zn-Y-Ti Alloy

Chemical, microstructure, and mechanical property of TiAl alloys produced by high-power direct laser deposition

Structural transformation behavior in a high Nb–TiAl alloy additively manufactured by laser powder bed fusion

Formation of lamellar microstructure in Ti-48Al-7Nb-2.5V-1Cr alloy

Simultaneously Enhancing the Strength and Ductility of Lamellar Ti–6Al–4V Alloy Via Designing Hierarchical 3D Nanolayered Structure

Microstructures and Mechanical Behaviors of a Directional Lamellar Ti-48Al-2Cr-2Nb Alloy Produced by Laser Additive Manufacturing

Long-period Stacking Ordering Induced Ductility of Nanolamellar TiAl Alloy at Elevated Temperature

Phase Equilibria of Long-Period Stacking Ordered Phase in the Ternary Mg-Y-Al Alloys

Microstructure Evolution and Phase Transformations in Ti-22Al-25Nb Alloys Tailored by Super-Transus Solution Treatment

The Crystal Structure, Microhardness and Thermal Stability of the Ti26Al55Zn19 Alloy

Evolution of Microstructural Complex Transitions in Low-Modulus Β-Type Ti-35Nb-2Ta-3Zr Alloy Manufactured by Laser Powder Bed Fusion

Study of microstructure and compressive strength of a novel Ti-0.75Al-9.5V alloys manufactured by laser deposition melting

Microstructure Formation and Tailoring of the Intermetallic TiAl Alloy Produced by Direct Laser Deposition

Phase transformation mechanism and mechanical properties of Ti-45Al-8Nb alloy prepared by directed laser deposition

Microstructures and Phases in Electron Beam Additively Manufactured Ti-Al-Mo-Zr-V/CuAl9Mn2 Alloy