Abstract:In this study, the high-temperature stability and the generation mechanism of the Portevin–Le Chatelier (PLC) effect in solid-solution Mg–1Al–12Y alloy with different heat treatment processes were investigated by adjusting the content of long-period stacking ordered (LPSO) phases. It was found that the content of LPSO phases in the alloys differed the most after heat treatment at 530 °C for 16 h and 24 h, with values of 13.56% and 3.93% respectively. Subsequently, high-temperature tensile experiments were conducted on these two alloys at temperatures of 150 °C, 200 °C, 250 °C, and 300 °C. The results showed that both alloys exhibited the PLC effect at temperatures ranging from 150 to 250 °C. However, at a temperature 300 °C, only the alloy with a greater concentration of LPSO phases exhibited the PLC effect, whereas the alloy with a lower proportion of LPSO phases did not exhibit this phenomenon. Additionally, both alloys exhibited remarkable high-temperature stability, with the alloy containing a greater percentage of LPSO phases also demonstrating superior strength. The underlying mechanism for this phenomenon lies in the exceptional high-temperature stability exhibited by the second phase within the alloy. Furthermore, the LPSO phase effectively obstructs the movement of dislocations, and it also undergoing kinking to facilitate plastic deformation of the alloy. The results indicate that the PLC effect can be suppressed by reducing dislocation pile-up at grain boundaries, which leads to a decrease in alloy plasticity but an increase in strength. The presence of the PLC effect in the WA121 alloy is attributed to the abundant dispersed second phase within the alloy, which initially hinders the movement of dislocations, leading to an increase in stress, and subsequently releases the dislocations, allowing them to continue their movement and thereby reducing in stress.

Long-period Stacking Ordering Induced Ductility of Nanolamellar TiAl Alloy at Elevated Temperature

Revealing interface-assisted plastic anisotropy <i>via in situ</i> transmission electron microscopy tension of lamellar TiAl

Effect of the Morphology of Long-Period Stacking Ordered Phase on Mechanical Properties and Corrosion Behavior of Cast Mg-Zn-Y-Ti Alloy

Breaking the high-temperature strength-ductility trade-off in TiAl alloys through microstructural optimization

Evading the strength-ductility trade-off at room temperature and achieving ultrahigh plasticity at 800°C in a TiAl alloy

Highly Pressurized Helium Nanobubbles Promote Stacking-Fault-mediated Deformation in FeNiCoCr High-Entropy Alloy

Unraveling hot deformation behavior and microstructure evolution of nanolamellar TiAl/Ti3Al composites

Extraordinary superplasticity at low homologous temperature and high strain rate enabled by a multiphase nanocrystalline network

Simultaneously Enhancing the Strength and Ductility of Lamellar Ti–6Al–4V Alloy Via Designing Hierarchical 3D Nanolayered Structure

Temperature Effect on Stacking Fault Energy and Deformation Mechanisms in Titanium and Titanium-aluminium Alloy

High-Temperature Stability of Mg–1Al–12Y Alloy Containing LPSO Phase and Mechanism of Its Portevin–Le Chatelier (PLC) Effect

Extraordinary room temperature tensile ductility of laminated Ti/Al composite: Roles of anisotropy and strain rate sensitivity

Drastic enhancement in hot-workability and microstructural refinement of TiAl alloys via martensitic transformation: A comparative study

Enhanced Mechanical Properties of Ti-5Al-5Mo-5V-3Cr-1Zr by Bimodal Lamellar Precipitate Microstructures Via Two-Step Aging

Trifunctional nanoprecipitates ductilize and toughen a strong laminated metastable titanium alloy

The α 2 to orthorhombic O-phase transformation-facilitated high elastically mediated strain transfer ability in high Nb-TiAl alloys

Formation mechanism of lamellar bimodal microstructure and mechanical property in the high temperature near α titanium alloy

Stable strain hardening behavior of Ti-4Al-5Mo-5V-5Cr-1Nb alloy during plastic deformation

Evolutionary mechanisms in the plastic deformation of γ'-Ni 3 (Al, Ti)-strengthened additively manufactured nickel-based 939 superalloys at intermediate temperatures

Strength enhancement of a bi-lamellar PM Ti–6Al–4V alloy without sacrificing ductility by Al partitioning and twinning-induced plasticity effect

Peritectic Solidification Kinetics and Mechanical Property Enhancement in a Rapidly Solidified Ti–48 at% Al–8 at% Nb Alloy via Hierarchical Twin Microstructure