Abstract:Ti2AlNb alloy is a new type of lightweight and heat-resistant structural material that has been an active research topic with multi-phases due to its improved mechanical properties. However, the phase response under severe plastic deformation (SPD) at high strain rates is unclear, which limits the understanding of its strengthening mechanism. Here, laser shock peening (LSP) was employed to investigate the microstructure response of alpha 2, O, and B2/beta phases in Ti2AlNb alloy. After LSP, the highest density dislocations were generated in the B2/beta phases, followed by the O phases, and the least dislocations were observed in the alpha 2 phases. In the B2/beta phases, only dislocation tangles (DTs) were observed. Dislocation lines (DLs) and DTs were mainly distributed in the O phases. As for the alpha 2 phases, DLs were generated while a small number of DTs were piled up at the grain boundaries. In addition, parallel dislocations (PDs) with a spacing of about 135 nm can be observed on the surface of the alpha 2 phases, and the dislocations interspersed between PDs were composed of screw dislocations with long segments. In addition to dislocation structures, stacking faults (SFs) were observed in both alpha 2 phases and O phases, and mechanical twins were formed in the O phases, which were generated to coordinate the SPD induced on the surface. These dislocation structures formed dislocation cells (DCs) and sub-grain boundaries which further developed into high-angle grain boundaries (HAGBs) together with mechanical twins, dividing the coarse grains and refining the microstructure. As the depth increased, the responses of the three kinds of phases decreased. The PDs in the alpha 2 phases have widened spacing and could not penetrate the grains. The mechanical twins were gradually reduced until no obvious twin structure could be observed. Finally, dislocations, grain size, microhardness, and residual stress presented a gradient distribution. The improved microhardness (maximum 470 HV) and compressive residual stress (maximum -600 MPa) which were consistent with the refined grains and highdensity dislocations gradually decreased to that of the base metal (BM).

Alternative-band microstructure and LPSO phase in TiAl alloy produced by direct laser deposition

Investigation on the Microstructure and Mechanical Behaviors of a Laser Formed Nb-Ti-Al Alloy

Microstructure characteristics of a γ single-phase Ti-55Al-7.5Nb alloy fabricated via additive manufacturing

In-situ Investigation of the Anisotropic Mechanical Properties of Laser Direct Metal Deposition Ti6Al4V Alloy

Phase transformation mechanism and mechanical properties of Ti-45Al-8Nb alloy prepared by directed laser deposition

Study of microstructure and compressive strength of a novel Ti-0.75Al-9.5V alloys manufactured by laser deposition melting

Structural transformation behavior in a high Nb–TiAl alloy additively manufactured by laser powder bed fusion

Evolution of microstructure and mechanical property of Ti-47Al-2Cr-2Nb intermetallic alloy by laser direct energy deposition: From a single-track, thin-wall to bulk

Investigation of Ti2AlNb-Added TiAl Composite Prepared by Direct Laser Deposition

Direct bonding of bimetallic structure from Ti6Al4V to Ti48Al2Cr2Nb alloy by laser additive manufacturing

Formation Mechanism of Dilute Region and Microstructure Evolution in Laser Solid Forming TA15/Ti2AlNb Dual Alloy

Microstructure of a Ti–50 Wt% Ta Alloy Produced Via Laser Powder Bed Fusion

Gradient microstructure response in different phases of Ti<sub>2</sub>AlNb alloy with laser shock peening

Laser Powder Bed Fusion of Titanium Aluminides: An Investigation on Site-Specific Microstructure Evolution Mechanism

Grain refinement and columnar-to-equiaxed transition of Ti6Al4V during additive manufacturing via different laser oscillations

Microstructure evolution and tensile property of TiAl alloy using continuous direct energy deposition technique

Investigation of the Microstructure of Ti6Al4V Alloy by Coaxial Double Laser Metal-Wire Deposition

Solidification Microstructure Prediction of Ti-6Al-4V Alloy Produced by Laser Melting Deposition

Fabrication of Ti3Al-Based Intermetallic Alloy by Laser Powder Bed Fusion Using a Powder Mixture

Effect of annealing treatment on microstructure and tensile properties of Ti-48Al-2Cr-5Nb alloy fabricated by laser additive manufacturing

The ageing response of direct laser deposited metastable β-Ti alloy, Ti–5Al–5Mo–5V–3Cr