Abstract:The research on Al–Zn–Mg–Cu alloys mainly focuses on the effects of solution aging and strain rate on the microstructure and properties of the alloy, as well as the flow stress behavior of the alloy. There are few studies on the effects of hot rolling deformation and reduction pass on the microstructure and properties of aluminum alloy. The dislocation density of alloy is affected by changing the rolling deformation, and post-heat treatment improves fine grains segregation and break coarse second phases. The alloys comprehensive mechanical properties are improved by controlling the recrystallization fraction and size. Different shape variable rolling and different passes, optical microscope (OM), field emission scanning electron microscope (SEM) with energy dispersive spectrometers (EDS), X-ray diffractometer (XRD), microhardness tester, and other methods were used to characterize the samples, and simulation of the rolling process analyzed by Deform-3D software. The effects of hot rolling deformation and deformation pass on microstructure and properties of aluminum alloy were also studied. The results show that dynamic recrystallization was beneficial to grain refinement when deformation increases to 40%. The coarse second phase was broken and refined into chains and partially spheroidized to dissolve in the matrix under large deformation. Dislocation density decreased after solution treatment when deformation was less than 80%, and increased after large deformation was 80%. The equivalent strain obtained by numerical simulations increases with the increase of deformation. The maximum equivalent strain was on both sides of the rolling surface, and this area was the most prone to crack in rolling. When the increase of the shape variable, the recrystallization volume fraction increased, and the grain size decreased.

Effect of Rolling with Different Amounts of Deformation on Microstructure and Mechanical Properties of the Mg–1Al–4Y Alloy

Effect of rolling deformation on microstructure and mechanical properties of Mg–Y–Nd–Al alloy

Effect of final rolling deformation on microstructure, work hardening and softening behavior of Mg-8Li-3Al-0.3Si alloys

Microstructure, texture and mechanical properties of the rolled high modulus Mg-Y-Zn-Al-Li alloy

Effect of Dual Deformation Processes on the Microstructure and Mechanical Properties of Low-Alloyed Mg-Zn-Ca-Mn Alloy

Effect of rolling temperature on deformation behavior and mechanical properties of Mg-8Li-1Al-0.6Y-0.6Ce alloy

Dynamic recrystallization, texture and mechanical properties of high Mg content Al–Mg alloy deformed by high strain rate rolling

Effect of Warm Rolling on the Microstructure, Texture and Mechanical Properties of Extruded Mg–Zn–Ca–Ce/La Alloy

Effect of rolling temperature on microstructure and mechanical properties of hot-rolled Mg-Al-Ca-Zn-Mn alloys

Effect of pack-rolling temperature on microstructure and mechanical properties of Mg-6Sn-3Al-1Zn Alloy

Effect of rolling deformation and passes on microstructure and mechanical properties of 7075 aluminum alloy

Effect of Deep-Cooling Rolling Deformation on the Microstructure and Mechanical Properties of an Al-4.5Cu-1.5Mg-0.6Mn-0.2Ti Alloy

Effects Of Rolling Process On Microstructure And Mechanical Property Of 7050 Aluminum Alloy

Effect of Rolling Deformation on Microstructure and Mechanical Properties of As-Cast and Rolled ZM21 Magnesium Alloy

Microstructure, Mechanical Properties and Texture Evolution of Mg–Al–Zn–La–Gd–Y Magnesium Alloy by Hot Extrusion and Multi-Pass Rolling

Non-basal Slips Mediated Dynamic Recrystallization Promote Synergistic Strengthening and Toughening of Centrifugal Casting Mg–1.1Mn–0.5Al Alloy via High Strain Rolling

Microstructure and Texture Evolution of Mg-3Zn-1Al Magnesium Alloy During Large-Strain Electroplastic Rolling

Effects of rolling processing on the microstructures, mechanical properties and strain softening behavior of biodegradable Zn-0.06 Mg alloy

Microstructure and mechanical property of multi-pass low-strain rolled Mg-Al-Zn-Mn alloy sheet

Research on Effects of Rolling-Drawing Deformation on Performance of Cu-10Ni-1Fe-1Mn Alloy

Enhanced Mechanical Properties of Extruded Mg–Y–Zn Alloy Fabricated Via Low-Strain Rolling