Abstract:This report focuses on the evaluation of the electrochemical properties of both solution-deposited sol-gel (sg-ZnO) and sputtered (sp-ZnO) zinc oxide thin films, intended for use as electron-collecting interlayers in organic solar cells (OPVs). In the electrochemical studies (voltammetric and impedance studies), we used indium-tin oxide (ITO) over coated with either sg-ZnO or sp-ZnO interlayers, in contact with either plain electrolyte solutions, or solutions with probe redox couples. The electroactive area of exposed ITO under the ZnO interlayer was estimated by characterizing the electrochemical response of just the oxide interlayer and the charge transfer resistance from solutions with the probe redox couples. Compared to bare ITO, the effective electroactive area of ITO under sg-ZnO films was ca. 70%, 10%, and 0.3% for 40, 80, and 120 nm sg-ZnO films. More compact sp-ZnO films required only 30 nm thicknesses to achieve an effective electroactive ITO area of ca. 0.02%. We also examined the electrochemical responses of these same ITO/ZnO heterojunctions overcoated with device thickness pure poly(3-hexylthiophehe) (P3HT), and donor/acceptor blended active layers (P3HT:PCBM). Voltammetric oxidation/reduction of pure P3HT thin films on ZnO/ITO contacts showed that pinhole pathways exist in ZnO films that permit dark oxidation (ITO hole injection into P3HT). In P3HT:PCBM active layers, however, the electrochemical activity for P3HT oxidation is greatly attenuated, suggesting PCBM enrichment near the ZnO interface, effectively blocking P3HT interaction with the ITO contact. The shunt resistance, obtained from dark current-voltage behavior in full P3HT/PCBM OPVs, was dependent on both (i) the porosity of the sg-ZnO or sp-ZnO films (as revealed by probe molecule electrochemistry) and (ii) the apparent enrichment of PCBM at ZnO/P3HT:PCBM interfaces, both effects conveniently revealed by electrochemical characterization. We anticipate that these approaches will be applicable to a wider array of solution-processed interlayers for "printable" solar cells.

Towards Transparent Conductive Zinc Oxide Films As Effective Anodes in Organic Photovoltaics

Indium-Doped Zinc Oxide Thin Films As Effective Anodes of Organic Photovoltaic Devices

Flexible Organic Photovoltaics from Zinc Oxide Nanowires Grown on Transparent and Conducting Single Walled Carbon Nanotube Thin Films

Efficient Organic Photovoltaics Using Solution-Processed, Annealing-Free TiO2 Nanocrystalline Particles As an Interface Modification Layer

Solution-Processed ZnO with Conductivity over 1000 S Cm-1 for ITO-Free Organic Photovoltaics.

Characterization of ZnO Interlayers for Organic Solar Cells: Correlation of Electrochemical Properties with Thin-Film Morphology and Device Performance

Electrodeposition Zinc-Oxide Inverse Opal and Its Application in Hybrid Photovoltaics

An Anode with Aluminum Doped on Zinc Oxide Thin Films for Organic Light Emitting Devices

Enhanced Performance And Stability Of Polymer Solar Cells By In Situ Formed Alox Passivation And Doping

A Transparent Electrode Based on Solution-Processed ZnO for Organic Optoelectronic Devices

Polarized Thin Layer Deposited Electrochemically on Aluminum-Doped Zinc Oxide As a Cathode Interlayer for Highly Efficient Organic Electronics.

Electronic Structure Effect of Polythiophene Derivatives and Nano N-Zn-Ag/TiO 2 on Performance of Organic Thin Film Solar Cell

Highly Efficient Organic Photovoltaic Devices Using F-Doped Sno2 Anodes

Increased Efficiency For Perovskite Photovoltaics Based On Aluminum-Doped Zinc Oxide Transparent Electrodes Via Surface Modification

Realizing the Ideal Structure for Hybrid Photovoltaics by Directly Electrochemical Polymerizing Thiophene Between ZnO Nanorods

Influence of ZnO Interlayer on the Performance of Inverted Organic Photovoltaic Device

Increased Electron Transport and Hole Blocking in an Aqueous Solution Processed Dye-Doped ZnO Cathode Interlayer for High Performance Organic Solar Cells

Organic Photovoltaic Cells with Stable Top Metal Electrodes Modified with Polyethylenimine

Semitransparent Polymer-Based Solar Cells with Aluminum-Doped Zinc Oxide Electrodes

Zinc Oxide Modified with Benzylphosphonic Acids as Transparent Electrodes in Regular and Inverted Organic Solar Cell Structures

Amorphous oxide alloys as interfacial layers with broadly tunable electronic structures for organic photovoltaic cells