Abstract:A site-specific xenon plasma focused ion beam preparation technique for microcantilever samples (1-20 µm width and 1:10 aspect ratio) is presented. The novelty of the methodology is the use of a chunk lift-out onto a clean silicon wafer to facilitate easy access of a low-cost probe type indenter which provides bending force measurement. The lift-out method allows sufficient room for the indenter and a line of sight for the electron beam to enable displacement measurement. An electroplated nanotwinned copper (NTC) was cut to a 3 × 3 × 25 µm microbeam and in situ mechanically tested using the developed technique. It demonstrated measured values of Youngs modulus of 78.7 ± 11 GPa and flow stress of 0.80 ± 0.05 GPa, which is within the ranges reported in the literature. LAY DESCRIPTION: In this paper a site specific method is present for making particularly small mechanical tests samples, of the order of 100th the size of a human hair. These small samples can then be used to determine the mechanical properties of the bulk material. Copper with a nano twinned grain structure is used as a test medium. Ion milling was used to cut the sample to shape and a micro probe was used for mechanical testing. Ion milling can cut away very small volumes of material as it accelerates ions at the surface of the sample, atomically machining the sample. Micro probes are a cost-effective small-scale load measurement devices, however, they require a large area for accessing the sample. The indenter requirements are a problem when making you samples with ion milling as ion millers are best at making small cuts. Our aim was to design a cutting strategy which reduces the amount of cutting required while allowing samples to be fabricated anywhere on the sample. We used a chunk lift out technique to remove a piece of material which is then welded to a wafer of silicon this gives sufficient space around the sample for ion milling and testing. The additional space allowed easy access for the probe. A 3 × 3 × 10 µm micro cantilever beam was cut out from copper, this beam was then bent. The force from bending and distance bent was measured and converted into Youngs modulus which is a measure of flexibility. The modulus value measured was comparable to the values reported in other papers.

A QuantitativeIn SituSEM Bending Method for Stress Relaxation of Microscale Materials at Room Temperature

Atomistic Numerical Investigation of Single-crystal Copper Nanowire with Surface Defects

In situ nanomechanical measurement of Cu nanowires

An investigation of the combined size and rate effects on the mechanical responses of FCC metals

Investigations of Micro-Deformation in Monocrystalline Copper at Low Temperatures via Indentation

Micro-cantilever bending tests for understanding size effect in gradient elasticity

Intermitted 3D diffraction tomography combined with in situ Laue diffraction to characterize dislocation structures and stress fields in micro bending cantilevers

In-Situ Tem Compression of Submicron-Sized Single Crystal Copper Pillars

A method to access the electro-mechanical properties of superconducting thin film under uniaxial compression

Coupled effect of specimen size and grain size on the stress relaxation of micron-sized copper wires

Measurement of Thermal Stress by X-ray Nano-Diffraction in (111)-Oriented Nanotwinned Cu Bumps for Cu/SiO2 Hybrid Joints

A mesoscale investigation of strain rate effect on dynamic deformation of single-crystal copper

SEM In-Situ Investigation on Failure of Nanometallic Film/substrate Structures under Three-Point Bending Loading

SEM In Situ Study on Deformation Behavior of Cu and Cu/Ni Films under Three-Point Bending

Stress–strain behavior of Cu on the AMB‐Si3N4 substrate undergoing thermal cycles via in situ strain measurement

Focused ion beam preparation of microbeams for in situ mechanical analysis of electroplated nanotwinned copper with probe type indenters

Computer experiments on nano-indentation: A molecular dynamics approach to the elasto-plastic contact of metal copper

Strain hardening in bent copper foils

Bending strain in 3D topological semi-metals

A Micro-Scale Strain Rosette for Residual Stress Measurement by SEM Moiré Method

Stress Relaxation and Grain Growth Behaviors of (111)-Preferred Nanotwinned Copper during Annealing