Abstract:Abstract The effect of thermal cycle on the residual stress, microstructural constituents, and alloying elements composition of dissimilar S690QT and 316L austenite stainless steel was studied. Finite element model (FEM) using ANSYS 19.1 software and an experimental investigation using gas metal arc welding (GMAW) process with fully austenite filler wire were applied to developed thermal cycle and evaluate residual stress in the heat-affected zone of both materials. The experimental data were recorded using a thermal-cycle sensor (TCS) and x-ray diffraction technique. A microstructural investigation was done using Scanning electron microscopy (SEM) and Energy-Dispersive x-ray Spectroscopy (EDS). The thermal cycle showed the maximum temperature ( T max ) in the HAZ of 316L side (850 °C) at a distance of 7 mm away from the centreline of the weld compare to S690QT side. The magnitude of tensile residual stresses in the 316L side decreased as welding heat input increased. The maximum residual stresses were observed on the S690QT side (700 MPa). Microstructural investigations revealed the formation of Bainite, and some retained of austenite at the temperature of 800 °C in the coarse grain heat-affected zone (CGHAZ) of S690QT. On 316L side, some grain boundary austenite (GBA), intragranular austenite (IGA), and carbides were observed in the CGHAZ. Compared to the initial microstructure of both materials, a slightly increase of Mn, Cr, and Si were observed at the respective values of 1.90%, 1.25%, and 0.40% on the S690QT side compared to the BM. For 316L side, it indicated an increase of Cr (26%), Mo (5.69%), and Ni (17%) in the alloying element composition compared to the BM. Applying 10 kJ cm −1 of heat input produced an excellent mechanical property and reduced the formation of carbide, inter-granular corrosion in the microstructure of 316L side.

Investigations into residual stresses in S690 cold formed circular hollow sections due to transverse bending and longitudinal welding

Assessing the Residual Stresses in Dissimilar Welded Joint: Depth-Sensing Indentation Testing and Numerical Simulation

Structural testing and numerical modelling of T-joints between cold-formed S690 circular hollow sections under brace in-plane bending

Experimental Investigation into High Strength S690 Cold-Formed Circular Hollow Sections under Compression

Numerical Study on Residual Stresses and Plastic Strains in Cold-Formed High-Strength Steel Circular Hollow Sections

Structural Behaviour of T-joints Between High Strength S690 Steel Cold-Formed Circular Hollow Sections

Investigations on material properties and residual stresses in cold-formed high strength steel irregular hexagonal hollow sections

Investigation on residual stress of EQ56 high strength steel butt weld

Experimental investigation and predictive models of membrane residual stresses in S690 high strength steel welded π-shaped and cruciform sections

Experimental Investigation and Modeling on Residual Stress of Welded Steel Circular Tubes

Effect of Post-Weld Heat Treatment on the Plastic Buckling of Welded Cylindrical Shells

Residual Stress Tests and Predictive Model of Friction Stir Welded Normal-Strength Aluminium Alloy H-shaped Sections

Effect of welding residual stress on the performance of CFST tubular joints

Multiphysics Study of Thermal Profiles and Residual Stress in Welding

Experimental and Numerical Study of Membrane Residual Stress in Q690 High-Strength Steel Welded Box Section Compressed Member

Experimental investigation on material properties and residual stresses in cold-formed high strength steel irregular octagonal hollow sections

Residual Stress of 460mpa High Strength Steel Welded Box Section: Experimental Investigation and Modeling

Thermal induced residual stress and microstructural constituents of dissimilar S690QT high-strength steels and 316L austenitic stainless steel weld joints

Material properties and residual stresses of high strength steel hexagonal hollow sections

Residual Stresses Simulation for Friction Stir Welded Joint

RESIDUAL STRESS OF WELDED I SECTIONS FABRICATED FROM HIGH PERFORMANCE STEEL: EXPERIMENTAL INVESTIGATION AND MODELLING