Abstract:The present work characterizes mechanical (elastic and plastic) properties and residual stresses of a Ni-Co thin film having 10 m thickness. Mechanical properties are obtained from direct-tension testing together with elastic finite element analysis. Membrane and bending components of residual stresses are measured using micro-cantilever and T-structure tests, respectively. Introduction Measurement of residual stresses in thin films is quite important, as their effect on mechanical integrity of micro-electrical-mechanical components could be significant. A number of measurement methods are available [1-7], but a majority of methods deal with measuring averaged residual stresses, rather than thickness-variation of residual stresses in thin films. Although such thickness variation could be often insignificant due to the fact that the thickness is very small, residual stresses can vary along the thickness of thin films. Measuring thickness variations of residual stresses, however, are not straightforward. A sectioning method can be applied (see for instance Ref. [7]), but can be quite tedious. In this respect, a simple method to measure thickness variations is desirable. In designing (macroscopic) structures, a stresses categorization process from stresses in the thickness direction is popularly employed [8-10]. In the stresses categorization process, stresses in the thickness direction are decomposed into the primary, secondary and peak stresses. Primary stresses are ones resulting mechanical loads and dead weights. Secondary stresses include thermal and residual stresses. Both primary and secondary stresses are typically idealized as a sum of (constant) membrane and (linear) bending stress components. Remaining stresses are classified as the peak stress, which relaxes quickly with plastic deformation by definition. A message that can be learnt from conventional stresses categorization process is that determination of membrane and bending components of residual stresses would be sufficient from mechanical integrity point of view. This paper presents measurement of residual stresses in Ni-Co thin films. A linearly-varying residual stress across the film thickness is assumed. To measure its bending and membrane components, cantilever beam and T-structure beam specimens are used, respectively. Experiments Material and Specimen Fabrication A NiCo thin film is recently widely used for MEMS devices using LIGA processes. Fabrication processes of NiCo thin film specimens are schematically shown in Fig. 1. For tensile test, conventional “dogbone” tensile test specimens were fabricated. Furthermore, for residual stress analysis, specimens of T-type structure and cantilever beams (which will be discussed later in this paper) with various dimensions were also fabricated. A single-side

Measurement of Residual Stress of MEMS Materials

RESIDUAL STRESSES IN MICRO-ELECTRO-MECHANICAL SYSTEMS

Overview of residual stress in MEMS structures: Its origin, measurement, and control

In-situ Measurement of Average Stress Gradient of a MEMS Thin-Film

Measurement Of Young'S Modulus And Residual Stress Of Micromembranes

A Novel Symmetric Test Structure For Residual Stress On Mems Thin Film

Measurement Of Residual Stress In Multilayered Thin Films By A Full-Field Optical Method

A Novel Residual Stress Test Structure for MEMs Thin Films

Research Progress of Residual Stress Measurement Methods

Residual stress and fracture of thick dielectric films for power MEMS applications

Study of techniques for measuring residual stress in micromachined films

The Stress Analysis of Si Mems Devices by Micro-Raman Technique

Residual Stress Measurement in Thin Films Using a Slitting Method with Geometric Phase Analysis under a Dual Beam (FIB/SEM) System

A new in situ residual stress measurement method for a MEMS thin fixed-fixed beam structure

Residual Stress Measurement on a MEMS Structure With High-Spatial Resolution

A Micro-Tensile Method for Measuring Mechanical Properties of Mems Materials

Investigation on the Release of Residual Stress in a Folded Structure Applied to MEMS Devices

Modification of curvature-based thin-film residual stress measurement for MEMS applications

Characterization of Mechanical Properties and Residual Stresses for Ni-Co Thin Films

A Novel Microstructure for In-Situ Measurement of Residual Stress in Micromechanical Thin Films