Abstract:The 2195 Al-Li alloy, as one of the representative third-generation Al-Li alloys, has extensive applications in lightweight aerospace structures. In this paper, the anisotropy in mechanical properties and microstructure evolution of 2195 Al-Li alloy sheets were investigated under a strain rate of 0.01, 0.1, 1 s-1 and a temperature of 440 and 500 °C. Experimental results showed that the hot tensile properties of the 2195 Al-Li alloy sheet exhibited a strong dependence on loading directions. The peak stress (PS) and elongation (EL) along the rolling direction (RD) were larger than the transverse direction (TD). For the tests carried out at 440 °C-1 s-1, the PS values of the sheets stretched along the RD and TD are 142.9 MPa and 110.2 MPa, respectively. And, most of the PS anisotropy values are larger than 15%. The anisotropy in EL is less significant than in PS. All the differences are about 10%. Moreover, dimples in the samples stretched along RD were more and deeper than those along TD at 440 °C. The fracture morphology along RD and TD were similar, and both were cleavage fractures at 500 °C. Particularly, the fractions of high angle grain boundaries (HAGBs) along TD were all about 5% larger than those of RD. And, there were more small-sized continuous dynamic recrystallization (CDRX) grains inside the initial grains and discontinuous dynamic recrystallization (DDRX) grains featured with the local bulge of grain boundaries along TD. This was due to the smaller average Schmid factor and the vertical EL trend of the initial grains when the samples were stretched along TD. A model of grain evolution during the dynamic recrystallization (DRX) along RD and TD was proposed based on EBSD results. The Schmid factor and banded structure had a more prominent effect on the hot ductility of the 2195 Al-Li alloy compared with the degree of DRX, thus presenting a higher EL and better hot ductility along RD.

Anisotropic Corrosion Behavior of Hot-Rolled Mg-8 Wt.%li Alloy

High corrosion resistance and weak corrosion anisotropy of an as-rolled Mg-3Al-1Zn (in wt.%) alloy with strong crystallographic texture

Effect of Rolling Ratios on the Microstructural Evolution and Corrosion Performance of an As-Rolled Mg-8 Wt.%li Alloy

Anomalous Evolution of Corrosion Behaviour of Warm-Rolled Type 304 Austenitic Stainless Steel

Microstructure and corrosion behavior of as-homogenized and as-extruded Mg−xLi−3Al−2Zn−0.5Y alloys (x=4, 8, 12)

Anisotropy of the Crystallographic Orientation and Corrosion Performance of High-Strength AZ80 Mg Alloy

Revealing distinct corrosion mechanisms of soluble as-extruded Mg–Er–Ni alloy with LPSO and Mg 2 Ni phase in different orientations

Enhancing Strength-Ductility Synergy and Corrosion Residual Strength of Hot-Rolled Mg-2Zn-0.85Y Alloy

Study of grain orientation effect on the corrosion behavior of biocompatible magnesium alloy Mg-2Zn-0.5Ca

Corrosion and Characterisation of Dual Phase Mg–Li–Ca Alloy in Hank’s Solution: the Influence of Microstructural Features

Comparison on corrosion resistance and surface film of pure Mg and Mg−14Li alloy

Influence of Hot Rolling on Microstructure, Corrosion and Mechanical Properties of Mg–Zn–Mn–Ca Alloy

Comparison of the Corrosion Behaviors of Mg–Gd–Y–Zn–Zr Alloys Fabricated by Different Preparation Methods

Modulation of corrosion properties by heat treatment and extrusion with mechanism analysis of high mechanical strength Mg-5.6Dy-3.1Ni alloy

Effect of Rolling Treatment on Microstructure, Mechanical Properties, and Corrosion Properties of WE43 Alloy

The Effect of Texture on the Corrosion Behavior of AZ31 Mg Alloy

Comparison of Microstructure, Mechanical Property, and Degradation Rate of Mg–1Li–1Ca and Mg–4Li–1Ca Alloys

Microstructure and Corrosion Behavior of the As-cast Mg-xAl (x=9%, 12%, 15%) Alloys

Effect of Initial Orientation on the Anisotropy in Microstructure and Mechanical Properties of 2195 Al-Li Alloy Sheet during Hot Tensile Deformation

Comparison of Corrosion Performance of Extruded and Forged WE43 Mg Alloy

Microstructure and corrosion resistance of ultrahigh pressure Mg-8Li based alloys