Abstract:A Cu-0.41Mg-0.06Ca (wt.%) alloy was processed by equal channel angular pressing (ECAP) for up to 12 passes via Bc route at room temperature, and its homogeneity was evaluated from three aspects of hardness, microstructure and crystallographic texture. The hardness was measured in detail on the whole transverse planes, and the microstructure and the crystallographic texture in the central and bottom regions on the transverse planes were investigated by electron backscatter diffraction (EBSD) technique. After 1 ECAP pass, the hardness in the central region was 9.4% higher than that in the bottom region; the microstructure in the central region consisted of the elongated grains, while that in the bottom region was composed of the slightly distorted grains; the crystallographic texture in the central region followed the ideal orientations of the ECAP crystallographic texture, nevertheless the crystallographic texture in the bottom region obviously deviated from any ideal orientation of the ECAP crystallographic texture. Then, with the increase of ECAP passes, the hardness and microstructure differences between in the two regions gradually weakened, and the deviation of the crystallographic texture in the bottom region gradually decreased. After 8 ECAP passes, the both regions showed the same hardness, the similar ultrafine-grained microstructure and the similar crystallographic texture. The difference formation should be attributed to the non-uniform strain caused by the friction between the sample and the die wall, rather than caused by the corner gap. The difference weakening should be attributed to the strain hardening behavior of metals. The strength calculation showed that the Cu-Mg-Ca alloy after 8 ECAP passes had almost the same yield strengths where 593 MPa for the central region and 583 MPa for the bottom region, showing only 1.7% difference.

Fracture Toughness Anisotropy of Ultrafine-Grained Pure Copper Processed by Equal Channel Angular Pressing

Tensile Deformation Behaviors of CuNi Alloy Processed by Equal Channel Angular Pressing

Tensile and Compressive Deformation Behaviors of Commercially Pure Al Processed by Equal-Channel Angular Pressing with Different Dies

Regarding fracture plane with minimum toughness and fracture anisotropy associated with elongated grain boundaries in ultra-fine-grained Cu

Numerical investigation of fracture behavior of nanostructured Cu with bimodal grain size distribution

Microscopic Analysis by EBSD Method on Fatigue Crack Propagation Behaviour in Ultrafine-Grained Copper

A comprehensive study on the damage tolerance of ultrafine-grained copper

Microstructural Evolution and Micro/Meso-Deformation Behavior in Pure Copper Processed by Equal-Channel Angular Pressing

1216 Nano-Scale Strength Analysis by EBSD and AFM Hybrid Method in Ultrafine-Grained Copper Processed by ECAP

Strain localization and ductile fracture mechanism of micro/mesoscale deformation in ultrafine-grained pure copper

Experimental Study on Pure Copper Subjected to Different Severe Plastic Deformation Modes

Microstructure Evolution and Cooperative Strengthening Mechanism of Copper–Aluminum Bimetal Continuous Equal Channel Angular Pressing-Annealing Process

Assessment of Anisotropic Tensile Strength Using a Modified Shear Punch Test for Cu–Cr–Zr Alloy Processed by Severe Plastic Deformation

Shear fracture mechanism in micro-tension of an ultrafine-grained pure copper using synchrotron radiation X-ray tomography

Micro/nanostructure high strength and high conductivity CuCrZr alloy prepared through equal channel angular pressing and aging treatment

Microstructure Evolution and Mechanical Properties of Fcc Metallic Materials Subjected to Equal Channel Angular Pressing

Direct Observation of Shear Deformation During Equal Channel Angular Pressing of Pure Aluminum

Anisotropy in Fracture Toughness and Toughening Mechanism of Ti-22Al-25Nb Alloy Related to Texture and Grain Boundary Damage

Effect of Route on Tensile Anisotropy in Equal Channel Angular Pressing

Tensile Fracture of Ultrafine Grained Aluminum 6061 Sheets by Asymmetric Cryorolling for Microforming

APPROACH TO MEASURING DUCTILE FRACTURE TOUGHNESS FOR SOME HIGHER TEARING RESISTANCE METALS