Abstract:Features peculiar to the synthesis of SiC–Si 3 N 4 –Si 2 N 2 O composite powder with a controlled content of silicon carbide, nitride, and oxynitride phases, as well as the structure and properties of hot-pressed ceramics produced from this powder, were examined. The optimal composition of the synthesized SiC–Si 3 N 4 –Si 2 N 2 O powder was achieved by heating a 1 : 3 mixture of thermally expanded graphite (TEG) and silicon up to 1200°C in air. The interaction of TEG with fine silicon at 1200°C led to the formation of a solid solution of carbon in silicon carbide, accompanied by heat release. The generated heat increased temperature within localized volumes of the TEG cellular structure to a level where air nitrogen facilitated the development of silicon nitride and oxynitride and an amorphous phase. The amorphous phase crystallized as the interaction time increased to 2.5 h. The duration of the process influenced the final distribution of the phases, formed with the participation of CO, SiO, and air nitrogen. The microstructure of the synthesized powder was characterized by a general agglomerated state, resulting from rod and plate forms of Si 3 N 4 and Si 2 N 2 O. Hot pressing of the synthesized SiC–Si 3 N 4 –Si 2 N 2 O composite powder with Al 2 O 3 and Y 2 O 3 activators yielded superfine ceramics, possessing enhanced hardness and fracture toughness (HV10 = 20.7 GPa and K Ic = 6.5 MPa · m 1/2 ). The structure of the ceramics sintered at 2000°C differed from those sintered at 1850°C, primarily by higher density and average grain size. The superfine state significantly influenced the abrasive wear resistance of the ceramics in dry friction conditions. The linear wear index of a sample with an average size of structural elements varying from 0.2 to 1.5 μm was 111 μm/km at a sliding speed of 1 m/sec under a load of 0.2 MPa. This was significantly lower than the linear wear index of industrial ceramics of reaction-sintered silicon carbide (RSSC), which was 232.4 μm/km.

C0.3N0.7Ti-SiC Toughed Silicon Nitride Hybrids with Non-Oxide Additives Ti3SiC2.

C<sub>0.3</sub>N<sub>0.7</sub>Ti-SiC Toughed Silicon Nitride Hybrids with Non-Oxide Additives Ti<sub>3</sub>SiC<sub>2</sub>

New Route to Improve the Fracture Toughness and Flexural Strength of Si3N4 Ceramics by Adding FeSi2

Optimization of Microstructure to Improve Si3n4 Ceramics with Thermal Conductivity and Mechanical Properties: Effect of Si and Α-Si3n4 Powder Composition

Densification and Mechanical Properties of Si3N4/SiC Nanocomposite Using Si-Nitrided Si3N4 Powder

Fabrication and Mechanical Properties of Si3N4/SiC Nanocompoisites under Pressureless Sintering.

Si3N4-SiC ceramic nanocomposites

Fabrication and Mechanical Properties of SiC Reinforced Reaction-Bonded Silicon Nitride Based Ceramics

Novel (Zr, Ti)(C, N)–SiC ceramics via reactive hot-pressing at low temperature

Significant improvements of the relative density, microhardness, and fracture toughness of SiC via the addition of Ni3Al and Mg2Si

Novel Α/β SiC-(Ti, Nb)B2 Toughened (ti, Nb)C-based Composites with Enhanced Mechanical Properties Fabricated by in Situ Reactions Sintering at Low Temperature

Fabrication of high performance silicon nitride ceramics with TiO2 additive by annealing process

Mechanical Properties of Reaction-Bonded Si3n4/Sic Composite Ceramics

Effect of SiC Addition on Mechanical Properties of Hot-Pressed Al2O3-GdAlO3 Ceramics with Eutectic Composition

Preparation and Properties of Silicon Carbide Ceramics Enhanced by TiN Nanoparticles and SiC Whiskers

Properties of reaction-bonded SiC/Si3N4 ceramics

Synthesis of Ti<sub>3</sub>SiC<sub>2</sub> from TiC and Si and its toughening mechanism with incorporated carbon fibers

Effects of SiC Amount on Phase Compositions and Properties of Ti 3 SiC 2 -Based Composites

Synthesis and Mechanical Properties of In-Situ Hot-Pressed Ti3SiC2 Polycrystals

Sintering Behavior, Microstructure and Mechanical Properties of Silicon Carbide Ceramics Containing Different Nano-Tin Additive

Synthesis and Consolidation of Composite Materials in the SiC–Si3N4–Si2N2O System