Abstract:Introduction Ge is one of the most promising channel materials to further improve the performance of Si CMOS due to its high hole and electron mobility [1-3]. In order to overcome the current Si FinFET technology, 3D channel structure is mandatory for Ge MOSFETs. To fabricate Ge Fins, CF4- or SF6-based RIE etching is usually employed for Ge etching [Ref. needed]. However, both CF4 and SF6 RIE etching results in large surface roughness which strongly degrades the performance of Ge FinFETs. On the other hand, it is necessary to realize high selectivity of anisotropic etching of Ge which is important to obtain superior static electrical control of Fin channel. In this research, we developed a SF6-CF4 cyclic RIE etching method for Ge Fin formation with suppressed surface roughness. The impact of inserting SF6-O2 etching steps into CF4-O2 etching process on the surface roughness of Ge was systematically investigated, as well as the ratio of vertical etching to horizontal etching of Ge. It is found that with a time proportion of 60% for SF6-O2etching steps, a minimum RMS of 1.1 nm is obtained for Ge Fin etching. Experiments The CF4-O2 and SF6-O2 RIE cyclic etching were carried out for (100) Ge surfaces with the same pressure, plasma power and total gas flow. Different time proportions of 0%, 20%, 40%, 60%, 80% and 100%, were used for SF6-O2 etching steps during the CF4-O2etching, with a total etching time of each cycle for 20 s. The selectivity of vertical and horizontal etching of Ge was examined using SEM, and the surface roughness of Ge after etching was evaluated using AFM. Results and discussion Figure 1 shows the etching rate of CF4-O2 and SF6-O2 cyclic etching with different time proportion of SF6-O2 step. It is observed that the etching rate significantly increases with increase of SF6-O2 etching proportion, due to the high reactivity of SF6 with Ge [4]. The RMS of Ge surfaces after CF4-O2 and SF6-O2 cyclic etching for 20 s is evaluated by AFM (Figure 2). It is confirmed that large amount of surface roughness is generated for Ge surface after both CF4-O2 and SF6-O2 etching. With introducing SF6-O2 etching steps into CF4-O2 etching, the surface roughness of Ge is obviously reduced. The RMS values of Ge surface after CF4-O2 and SF6-O2 cyclic etching are summarized in Figure 3 as a function of the time proportion of SF6-O2 etching. It is found that with a time proportion of 60% for the SF6-O2 step, a minimum RMS of 1.1 nm is obtained for the Ge surface. The impact of SF6-O2 proportion to the ratio of vertical and horizontal etching for Ge is also examined, as shown in Figure 3. It is found that the selectivity of vertical etching decreases with increasing the SF6-O2 proportion. However, a relatively high selectivity of vertical etching of over 4 is still maintained with a time proportion of 60% for SF6-O2etching, resulting in Ge Fins with superior morphology (Figure 4). Conclusion A CF4-O2 and SF6-O2 cyclic etching method is proposed for Ge Fin formation. It is found that with a time proportion of 60% for SF6-O2etching step, superior morphology is achieved for Ge Fins with sufficiently suppressed surface roughness of 1.1 nm. References [1] S. Takagi, et al. IEDM, 2003. [2] H. Shang, et al. IBM. J. Res. Dev., 2006. [3] K. C. Saraswat, et al., Microelectro. Eng., 2008. [4] A. Campo, et al. J. Vac. Sci. Technol. B, 1995.

Reactive ion etching of Ge-Sb-Se ternary chalcogenide glass films in fluorine plasma

Reactive ion beam etching for diffractive optical elements

Rib and strip chalcogenide waveguides based on Ge-Sb-Se radio-frequency sputtered films

CHF 3 /O 2 -Based Plasma Reactive Ion Etching of GeTe for Nonvolatile Phase Change Memory

Chalcogenide Coatings of Ge_15Sb_20S_65 and Te_20As_30Se_50

A Systematic Study on Dry Etching Process of Germanium for Ge 3D-Fets Applications

Reactive ion etching of Germanium using SF6/CHF3/He gas mixture

Demonstration of High-Performance, Sub-Micron Chalcogenide Glass Photonic Devices by Thermal Nanoimprint

Reduction of Reactive-Ion Etching-Induced Ge Surface Roughness by SF 6 /CF 4 Cyclic Etching for Ge Fin Fabrication

Research on Ar/CHF3 reactive ion beam etching of SO2

Reactive ion etching of plasma enhanced chemical vapor deposition amorphous silicon and silicon nitride: Feeding gas effects

Inductively coupled plasma-reactive ion etching of InSb using CH[sub 4]∕H[sub 2]∕Ar plasma

Reactive ion etching of SiC thin films using fluorinated gases

Inductively Coupled Plasma-Reactive Ion Etching Of Insb Using Ch4/H-2/Ar Plasma

Reduction of RIE Induced Ge Surface Roughness by SF6-CF4 Cyclic Etching Method

Research on Ar/CHF_3 Reactive Ion Beam Etching of SiO_2

Understanding Aging in Chalcogenide Glass Thin Films Using Precision Resonant Cavity Refractometry

Fabrication of Slanted Grating Utilizing Reaction Ion Beam Etching: The Role of CHF<inf>3</inf> and O<inf>2</inf> Etching Atmosphere

Fabrication of Ternary Ge–Se–Sb Chalcogenide Microlens Arrays Using Thermal Reflow

Study on Fabrication and Optical Properties of Ge-Sb-Se Thin Films

Study on the Reactive Ion Etching of Si_3N_4