Abstract:The non-associated flow rule (non-AFR), which has been proved with advantages in accurately predicting yield stress components and Lankford coefficients, has different definitions for yield function and plastic potential function. Currently, there are two typical approaches to determine the plastic strain for non-AFR, one is called simple method which still uses the equivalent plastic strain (EPS) to calculate the plastic strain tensor, while the other is called full method which adopts the plastic compliance factor. Many researchers prefer to adopt the simple method in calculating the plastic strain due to its higher computation efficiency and its acceptable accuracy like the full method for some materials. However, the limitation and application condition of the simple method are still ambiguous. In the present work, a restriction for calculating the parameters in plastic potential function for the simple method is clarified and the limitation of the simple method has also been investigated. It is found that if the relative error of the difference between the yield function value and that of plastic potential function is within ±5% and hardening exponent is in the range of 0.1–0.3, the maximum absolute value of the relative error of the stress predicted by the simple method can be controlled less than 1.6%. Besides, an effective approach is introduced to reduce the error of the stress predicted by these two methods, which can improve the applicability of the simple method for those materials with the relative error of the difference between the value of yield function and that of plastic potential function is less than 10%. In order to have deeper understanding about their applicability, the two methods are compared under uniaxial tension along different orientations for AA2090-T3 and AA2008-T4 with the fully implicit return-mapping scheme. Fracture simulations of AA2090-T3 have also been conducted by introducing different methods. The results show that during the loading in transverse direction, the difference of EPSs predicted by these two methods is very small for AA2008-T4, while for AA2090-T3, the EPS predicted by the simple method is almost twice of that calculated by the full method. This further indicates that the applicability of the simple method mainly depends on the characteristics of materials.

An Extended Sequential Limit Analysis Based on Moving Coordinates for Pressurized Spherical Cap Membranes with Large Shape Change

Extension and Validation of Sequential Limit Analysis for Geotechnical Problems

Sequential Limit Analysis for Clamped Circular Membranes Involving Large Deformation Subjected to Pressure Load

Unified Plastic Limit Solution for Thick-Walled Cylinder with Size Effect

A New Design Method For Axially Loaded Thin-Walled Cylindrical Shells Based On Elasto-Plastic Buckling Analysis

Autofrettage and Shakedown Analyses of an Internally Pressurized Thick-Walled Spherical Shell Based on Two Strain Gradient Plasticity Solutions

Localized Perturbation Load Approach for Buckling Design of Thin-Walled Steel Cylindrical Shells under Partial Axial Compression

Plastic Limit Load Analysis for Pressure Pipe with Incomplete Welding Defects Based on the Extended Net Section Collapse Criteria

Isogeometric Method for Buckling Prediction and Post-Buckling Analysis of Variable Stiffness Composite Underwater Pressure Shell

Design of Axially Loaded Isotropic Cylindrical Shells Using Multiple Perturbation Load Approach – Simulation and Validation

Limit pressure and design criterion of cylindrical pressure vessels with nozzles

FINITE ELEMENT ANALYSIS OF PLASTIC LIMIT LOADS OF LOCALLY THINNED ELBOWS UNDER INTERNAL PRESSURE AND IN-PLANE BENDING MOMENT

Parametric Modeling and Buckling Analysis of Stiffened Spherical Shell Based on ABAQUS

A finite element-based analysis approach for computing the remaining strength of the pressure equipment with a local thin area defect

A closed-form structural stress-strain relation and implications on plastic design limits in codes and standards

On the Calculation of Plastic Strain by Simple Method under Non-Associated Flow Rule

FINITE ELEMENT ANALYSIS OF A SUPERELASTIC SHAPE MEMORY ALLOY CONSIDERING THE EFFECT OF PLASTICITY

Compliant Assembly Variation Analysis of Scalloped Segment Plates with a New Irregular Quadrilateral Plate Element Via ANCF

Accurate prediction of shear buckling capacity of low-yield-strength steel considering plastic deformations

A novel plastic limit load solution for the orthotropic cylindrical shell with nozzle under internal pressure

Experimental and Modeling Investigation on Anisotropic Plastic Flow of Metal Plates under Nonproportional Loading Conditions