Abstract:Mo2FeB2-based cermets have wide applications in fields of wear resistance, corrosion resistance and heat resistance due to their simple preparation process, low-cost raw materials, and prominent mechanical properties. Herein, Mo2FeB2-based cermets with xMo (x = 43.5, 45.5, 47.5, 49.5, wt.%) were prepared by means of the vacuum liquid phase sintering technique. Investigations on the microstructure and mechanical properties of Mo2FeB2-based cermets with Mo addition were performed. Experimental results show that, with Mo content increasing, the average particle size decreases gradually, revealing that the grain coarsening of Mo2FeB2-based cermets is controlled by interface reaction. In addition, Mo2FeB2 grains gradually transform from an elongated shape to a nearly equiaxed shape. The improvement of Mo2FeB2 hard phase on the morphology is mainly due to the inhibition of solution-precipitation reaction by increasing Mo. Furthermore, the relative density of cermets decreases due to the reduced Fe content. When Mo content is 47.5 wt.%, a relatively small grain size of Mo2FeB2 is obtained (about 2.03 mu m). Moreover, with the increase in Mo content, hardness and transverse rupture strength (TRS) of Mo2FeB2-based cermets increase firstly and then decrease. Whereas, with increasing Mo content, the fracture toughness deteriorates gradually. When Mo content is 47.5 wt.%, the comprehensive mechanical properties of cermets are the best. The optimal raw material ratio for the preparation of Mo2FeB2-based cermets in this study is determined to be 47.5 wt.% Mo-6.0 wt.% B-Fe.

High-temperature cyclic oxidation behavior and mechanism of Mo2FeB2-based cermets with various boron contents

Formation and Oxidation Behavior of Mo-Si-B Composite Coatings with B-rich Interlayer Prepared by Slurry Sintering Method

Dual effects of Cr doping on the high-temperature oxidation behavior of Mo2FeB2-based cermets

Effect of Mo Content on In-Situ Anisometric Grains Growth and Mechanical Properties of Mo2FeB2-Based Cermets

Microstructure, mechanical properties, and corrosion resistance of Mo2(Fe,Ni)B2-based cermets prepared by reaction boronizing sintering

On the reaction mechanism of Mo2FeB2-based cermets and wear transition induced by self-lubricating tribo-oxide layer

Effect of synthetic Mo2FeB2 powder on the microstructure and mechanical properties of Mo2FeB2-based cermets

Improvement of high temperature oxidation behavior of Cr3C2-20 wt % Ni cermets by adding 1 wt % Mo

Microstructure and mechanical properties of newly synthesized Mo(Co,Fe)B cermets

On the dissolution and enhancement mechanisms of Cr doping in Mo2FeB2-based cermets

Isothermal and Cyclic Oxidation Behavior of Fe–B Based Alloys at 927 K

Effects of boron addition on the high temperature oxidation of MoSi2 alloys

Bulk Mo2FeB2 Based Cermets Fabricated by Mechanical Ball Milling and Reaction Boronizing Sintering

Sintering Mechanism, Microstructure Evolution and Nanomechanical Properties of Cr-added Mo2FeB2 Based Cermets

Influence of Boron Contents on Oxidation Behavior and the Diffusion Mechanism of Fe–B Based Alloys at 1073 K in Air

Microstructure and Properties of Ti(C,N)-Based Cermets with AlxCoCrFeNiTi Binder

Effect of V Doping on the Microstructure and Mechanical Properties of Mo2FeB2-based Cermets and Investigation on the Enhancement Mechanism

Interface-reinforced Mo2FeB2-based cermets prepared by multi-step sintering under rapid cooling

Oxidation Behavior of Multiphase Mo5SiB2 (T2)-Based Alloys at High Temperatures

Characterisation of boride layer formed on Fe–Mo binary alloys

Microstructure and oxidation behaviour of MoSi2 coating combined MoB diffusion barrier layer on Mo substrate at 1300 °C