Abstract:Abstract The article is aimed at the study of structural features and phase chemical composition in 3.6 wt.% C-15 wt.% Cr-2 wt.% Mo cast iron prepared with adding 0.50 wt.% boron. The work was fulfilled using optical and electron scanning microscopy, EDS, XRD, hardness measurement, and thermodynamic modelling. It was found that due to boron effect the cast iron acquired hypereutectic structure consisting of the primary M7C3 carbides (5.3 vol. %) and the eutectics based on M7C3 carbide (rosette-shaped cells) and M3C carbide (coarse-net-shaped cells or Ledeburite-shaped cells). The total amount of carbide phases was 51.8 vol.% whereas the volume fractions of M7C3-eutectic cells and M3C-eutectic cells were 21.0 vol.% and 74.7 vol.% respectively. The matrix comprised austenite, martensite and pearlite whereas austenite volume fraction was measured as 32 vol.%. Chromium and molybdenum were unevenly partitioned in phases performing the opposite character of a distribution. The primary carbides contained about 37 wt.% Cr and 1.6 wt.% Mo with the stoichiometry of (Fe3.88Cr2.76Mo0.22Mn0.12Si0.02)C3. Substantial part of carbide precipitates (primary and eutectic both) exhibited the duplex nature presenting Cr-rich/Mo-depleted core (M7C3 carbide) and Cr-depleted/Mo-rich shell (M3C carbide). Duplex carbides were closely adjusted to austenite + M3C eutectic cells to be the starting interface for their solidification. A minor amount of micron-sized areas with 67.5 wt.% Mo and 4.6 wt.% Si were observed to be presumed as M6C carbide. The cast iron was subjected to holding at 950 °C for 2 hours with subsequent oil-quenching. This treatment caused the precipitation of fine secondary carbides followed by the martensite transformation which resulted in significant hardness increase from 672 HV (as-cast) to 1038 HV. The solidification sequence is discussed in terms of structure observation and Thermo-Calc modelling.

Characterisation of boride layer formed on Fe–Mo binary alloys

Effects of boron content on the structure and magnetic properties of Fe81-xSi13BxMo2Cr1Cu1P2 nanocrystalline alloys

Effect of Boron Concentration in the Fe-Cr-Mo-(B,C) Hardfacing Alloys on the Microstructure and Mechanical Properties

Effect of Boron Concentration on the Solidification Microstructure and Properties of Fe‐Cr‐B Alloy

Effect of boron concentration on microstructures and properties of Fe–B–C alloy steel

Microstructure Evolution and Mechanical Properties of Fe–Cr–B Alloys with Varying Mo Additions

Bulk Mo2FeB2 Based Cermets Fabricated by Mechanical Ball Milling and Reaction Boronizing Sintering

Boronize Coatings Studied with a New Mass Transfer Model

Effect of Molybdenum Addition on Mechanical Properties of Oriented Bulk Fe2B Crystal

Comparative Investigation on the Stability, Electronic Structures and Mechanical Properties of Mo2FeB2 and Mo2NiB2 Ternary Borides by First-Principles Calculations

High-temperature cyclic oxidation behavior and mechanism of Mo2FeB2-based cermets with various boron contents

Effect of Molybdenum Content on the Hardenability and Precipitation Behaviors of Boron Steel Austenitized at High Temperatures

Influence of Boron Contents on Oxidation Behavior and the Diffusion Mechanism of Fe–B Based Alloys at 1073 K in Air

Effect of boron on microstructure evolution and properties of wear-resistant cast Fe–Si–Mn–Cr–B alloy

Influences of boron on the microstructural characteristics and wear performance of hypereutectic Fe-Cr-C-Mo-xB hardfacing alloy

Microstructure and some properties of powder-pack borided Ti–5Mo–5V–8Cr–3Al alloy with special attention to the microstructure at the interface TiB/substrate

Microstructure and Crystallography of Borides and Mechanical Properties of Fe–B–C–Cr–Al Alloys

Effect of Boron Additions on the Microstructural Evolution and Properties of Fe-Mo-Cu-Ni-C Sintered Steel

Enhancing the Catalytic Activity of Mo(110) Surface via Its Alloying with Submonolayer to Multilayer Boron Films and Oxidation of the Alloy: A Case of (CO + O2) to CO2 Conversion

Characterization of Microstructure and Phase Elemental Composition of 15 Wt.% Cr – 2 Wt.% Mo Cast Iron with Boron Addition

Characterization and Growth Kinetics of Borides Layers on Near-Alpha Titanium Alloys