Abstract:The manufacture of inertial-grade and tactical-grade diamond micro electro mechanical systems (MEMS) hemispherical resonator gyroscopes is limited by the manufacturing accuracy of the monocrystalline silicon hemispherical concave mold, on which the gyroscope shell is formed. To solve this problem, this paper presents a new method for micro-ultrasonic machining of microhemispherical molds for resonator gyroscopes using an ultraprecise ceramic entire-ball tool (UCET). To study the wear mechanism of the UCET and the influence of tool wear on the surface integrity and form accuracy of the microhemispherical mold, a mathematical model for the tool wear of micro-ultrasonic machining of microhemispherical molds with UCET is established and verified by experiments. The micro-ultrasonic amplitude, the abrasive material and the abrasive size is found to have significant influences on the tool wear of the UCET. The wear rates of tungsten carbide and silicon nitride ceramic tools are 2.22% and 3.64%, respectively, which are far less than the wear rate of 8.03% of bearing steel. The wear condition agrees with the theoretical model. The machining experiment shows that the radius change, ΔR, is 6.47 <i>µ</i>m of the microhemispherical mold processed by UCET, which is much better than 32 <i>µ</i>m of the micromold processed by micro-electro discharge machining at one time. After 10 continuous machining runs, the deviation rate of the form accuracy of the micromold is 1.71%, 3.71% and 24.21%, due to the wear of tungsten carbide, silicon nitride and bearing steel, respectively. It can be seen that micro-ultrasonic machining of microhemispherical molds using UCET has the characteristics of a high initial form accuracy, low wear rate, high integrity and form accuracy. This is a potentially effective method to obtain micromolds with high accuracy and surface integrity.

Improved HNA Isotropic Etching for Large-Scale Highly Symmetric Toroidal Silicon Molds with < 10-Nm Roughness

Manufacturing Fused Silica Hemispherical Resonators Using Polymer Glass Suspension and Replication Molding

Micro ultrasonic machining hemispherical mold for MEMS resonator gyroscope using a novel ultraprecise ceramic entire-ball tool

A Novel Method to Fabricate On-Chip Ultra-High-q Microtoroid Resonators

A High-Selectivity HNA Etching System for Bulk Micromachined Deep Holes with High Roundness

Achieving Submicron Sphericity in Bowl-Shaped Micro Hemispherical Resonators through Precision Molding Process

Controllable fabrication of periodic arrays of high-aspect-ratio micro-nano hierarchical structures and their superhydrophobicity

Hemispherical micro-resonators from atomic layer deposition

Fabrication of 2D silicon nano-mold by side etch lift-off method

A novel method of water bath heating assisted small ball-end magnetorheological polishing for hemispherical shell resonators

Decreasing Frequency Splits of Hemispherical Resonators by Chemical Etching

A Net-Shape Fabrication Process of Alumina Micro-Components Using a Soft Lithography Technique

Surface evolution of fused silica hemispherical resonators and its influence on the quality factor

Nanosphere lithography on silicon oxide for high aspect ratio cryo etching of vertically-align silicon structures

Application of Multi-Mask Layers for High Aspect Ratio Soft Mold Imprint

Hybrid Process of Fabricating High-Quality Micro Wine-Glass Fused Silica Resonators

A route to engineered high aspect-ratio silicon nanostructures through regenerative secondary mask lithography

Fabrication and surface treatment of silicon mold for polymer microarray

A Study on the Fabrication of Nanostructures with High Aspect Ratio and Large Area Uniformity

Fabrication System for Large-Area Seamless Nanopatterned Cylinder Mold Using the Spiral Laser Interference Exposure Method

SCS nano-structures fabricated by hybrid process of HNA selective etching and oxidization