Abstract:Highlights • The convection in the Cu pattern surface increase with the Cu layer thickness. • The mechanism of Cu layer improvement under high current density was explained. • The adsorption model of the convection-dependent additives during the high current density Cu pattern electroplating process was proposed. • The Cu pattern with excellent properties was electroplated under a current density of 8 ASD with an ultra-high rate of over 90 μm/h. Background Cu pattern electroplating plays an essential role in the interconnection and microstructure fabrication of high-power device packaging. However, improving efficiency while ensuring the preparation quality is an urgent breakthrough direction. Methods A new electrolyte formula suitable for the high-rate Cu pattern electroplating was put forward, including 300 mg/L polyethylene glycol (PEG, molecular weight=8000) and 6 mg/L thiazolinyl polydipropyl sulfonate (SH110). The mechanism of high-rate Cu pattern electroplating was investigated by the combination of fluid flow simulation and the electrochemical measurements including galvanostatic measurements (GMs) and cyclic voltametric (CV) tests. The Cu pattern was electroplated in the Haring-Cell with air bubble as the forced convection method. Significant findings The simulation results indicate that the flow rate on the ring-shaped cathodic pattern surface gradually increases with the Cu growing up, which also increase from the pattern surface to the bulk electrolyte. The GMs results suggest that the cathodic polarization of the convection-dependent additives raises with the current density, which is strengthened by strong convection with current density lower than 6 ASD but have the opposite effect with current density larger than 8 ASD. The CV tests indicating that the aggregation of weak convection and strong polarization promote the antagonistic effect between thiolate of SH110 and PEG, the nucleation and the electroplating rate. Nevertheless, the synergistic effect of thiazoline of SH110 and PEG are enhanced with strong convection and weak polarization. The adsorption model during the Cu pattern electroplating process is established and verified by electroplating experiment with the optimum current density of 8 ASD. The Cu pattern is mirror bright with the high electroplating rate of over 90 μm/h. Graphical abstract Download : Download high-res image (160KB) Download : Download full-size image

Numerical Simulation and Experiments to Improve Throwing Power for Practical PCB Through-Holes Plating

Influence of Electroplating Current Density on Through Silicon Via Filling

RETRACTED: Copper Electrodeposition in Through-Silicon Via under Galvanostatic Condition

Modeling the Copper Electrodeposition of Through-silicon-vias Corresponded to Linear Sweep Voltammetry

A Numerical Model for Bottom-Up Copper Electrodeposition of TSV with Additives

Potential-Dependence Of Additives Distribution In Copper Electrodeposition Via Filling

Recent Advances in Electroplating of Through-Hole Copper Interconnection

Toward Preeminent Throwing Power from a Novel Alkaline Copper Electronic Electroplating Bath with Composite Coordination agents

Computational and experiments exploration of convection on Cu filling characteristics of multiple aspect-ratio micro through-holes

High-Frequency Electrothermal Characterization of TSV-Based Power Delivery Network

Numerical Simulation of Optimizing Plating Uniformity of Interconnect Circuits on Printed Circuit Boards

Experimental and Numerical Simulation Study on Uniformity of Temperature and Flow Field in an Advanced Packaging Electroplating Cell

A transfer-adsorption model for forward understanding the synergistic effects of additives in through-hole uniform copper thickening

Analysis on the Effectiveness of the 20-H Rule Using Numerical Simulation Technique

Combined fluid flow simulation with electrochemical measurement for mechanism investigation of high-rate Cu pattern electroplating

Electrochemical behaviors of additives in high Cu(II) concentration solution for high-aspect-ratio through ceramic holes filling

Intercircuit: Electroplating with Cavities for Fast Fabrication of Complex and High-Performance 3D Circuits

A hybrid domain decomposition and optimization method for predicting electromagnetic emissions from printed circuit boards

Copolymer of Pyrrole and 1,4-Butanediol Diglycidyl as an Efficient Additive Leveler for Through-Hole Copper Electroplating

Promotion of High-Speed Copper-Filling Performance for Interconnections with Increasing Aspect-Ratio Using Compound Additives

Simulating the Influence of Supporting Electrolyte Concentration on Copper Electrodeposition in Microvias