Abstract:Results on a ferritic–martensitic steel and conventional and advanced austenitic steels at 450–650°C in 30 MPa supercritical CO2 (sCO2) with and without 1% O2 and 0.1% H2O additions have indicated that carburizing sCO2 environments will have lower maximum operating temperatures compared to steam plants. Pack Al and Cr coatings were evaluated at 600o and 650°C and showed some benefit for up to 2000 h. With the addition of impurities in the sCO2, the coatings were less protective at 650°C. The carburizing supercritical CO2 (sCO2) environment limits the use of lower cost steels in the lower temperature (450–650°C) portions of the sCO2 Brayton cycle because of concerns about internal carburization and embrittlement. Results on a ferritic–martensitic steel and conventional and advanced austenitic steels at 450–650°C in 30 MPa sCO2 with and without 1% O2 and 0.1% H2O additions have indicated that sCO2 environments will have lower maximum operating temperatures compared to steam plants. Pack Al and Cr coatings were evaluated at 650°C on T91 and 316H substrates and showed some benefit for up to 2000 h at 650°C, especially without impurities. However, characterization indicated Al2O3 was not formed and Cr‐rich carbides formed in the Cr coatings. With the addition of impurities in the sCO2, the coatings were less protective at 650°C. Subsequent exposures at 600°C in sCO2 showed similar behavior. Postexposure evaluations included measuring the bulk C content and room temperature tensile properties. Improvements were indicated but the tensile results were complicated by the high temperature pack coating process affecting the substrate properties.

Effect of CO2 Gas Pressure on Composition, Growth Rate, and Structure of Duplex Oxide Formed on 9cr Steel at 550 °C

Effect of Atmosphere on Duplex Oxide Formed on 9cr Steel at 550 °C

Carbon depositions within the oxide scale and its effect on the oxidation behavior of low alloy steel in low (0.1 MPa), sub-(5 MPa) and supercritical (10 MPa) CO2 at 550°C

High Temperature Oxidation Behavior of Co-20Re-25Cr-2Si Alloy at Different Oxygen Pressures

Revealing the Effect of O2, SO2 and H2O in Supercritical CO2 on the Corrosion Behavior of 316L Steel at Elevated Temperature

Study on Corrosion Characteristics of Heat-resistant Materials in Supercritical Carbon Dioxide Environment Containing Oxygen Impurities

Pre-oxidation Effect on Oxidation Behavior of F91 in Carbon Dioxide at 550 °C

Oxidation Behavior and Lifetime Prediction of Three Commercial Alloys Used in Power Plants at 550 °C in CO2 Environment

The oxidation of an equimolar FeCoNiAl medium-entropy alloy at 900 °C in various oxygen pressures

The oxidation of an equimolar FeCoNiAl medium-entropy alloy at 900 o C in various oxygen pressures

Temperature dependence of carbon deposits within oxide scale on CrMoV steel in atmospheric and supercritical CO2

Coordination of Pre-oxidation Time and Temperature for a Better Corrosion Resistance to CO2 at 550 °C

Effect of Impurities On the Compatibility of Steels in Supercritical CO2 at 450°-650°c

Corrosion and Mechanical Performance of Grade 92 Ferritic-Martensitic Steel After Exposure to Supercritical Carbon Dioxide

Simultaneous Oxidation and Carburization of a Fe-9Cr Alloy under Different Oxygen Pressures at 800 °C

Effect of Supercritical CO2 on Steel Ductility at 450°-650°C

Experimental Investigation of the Initial Stage of the Oxidation Mechanism of Co Coating for Solid Oxide Fuel Cell Interconnects at 650 °C

Effect of Fe on the Oxidation, Sulfidation and Carburization Behaviors of Alloys in CO2 Containing SO2

Effect of surface roughness at elevated temperature and pressure on the oxidation behaviour of co-based alloy

Evaluation of coated steels in supercritical CO2

Corrosion Performance of Heat-Resisting Steels and Alloys in Supercritical Carbon Dioxide at 650 °C and 15 MPa