Abstract:Nickel based superalloys are widely used in such applications as gas turbine blades due to their excellent mechanical properties at elevated temperatures. Oxidation is one of the life limiting factors at such temperatures since it accelerates failure mechanisms, e.g. fatigue and creep. In this project, oxidation behavior of Ni-3Al-4.8Ti-9.5Co-14Cr (wt.%) superalloy was investigated under various testing conditions. The alloy was investment-cast with preferential crystal growth direction [100]. Isothermal oxidation tests were carried out at 800°C for 150h. Cyclic oxidation tests were then conducted between 100-800°C for 150 one-hour cycles. An additional one-hour cycle was tested to replicate real-life working condition of the alloy, which consisted of heating the samples up to 800°C followed by slow cooling to 400°C. During the testing, samples were periodically taken from the furnace and weighted with an accuracy of 10 -4 g to calculate the weight gain and to analyze the microstructure of formed oxide. Scanning electron microscopy (SEM) combined with energy-dispersive spectroscopy (EDS) and X-ray diffraction were used to study the microstructure of oxidation products. The results reveal that the highest amount of weight gain is obtained in isothermal testing, while the lowest in cyclic. Diffusion of Ti and Ni to the free surface results in the early-stage formation of needle-shaped oxide phases followed by severe oxidation of Cr and Al. The layer of chromium oxide is continuous while aluminum oxide is blocky at the deepest position from the free surface. Cracks form at the interface of carbide particles and gamma phase near the free surface of cyclic oxidation samples due to concentration gradient of Ni and Al. Precipitate-free zone are observed near the free surface of all the samples at the end of the tests, but internal oxidation does not occur significantly in all the samples. It is found that temperature fluctuation increases oxide spallation, which causes crack formation. At the same time, in isothermal testing, dense, crack-free layer of oxide form on the surface of superalloy.

Oxidation Behavior and Lifetime Prediction of Three Commercial Alloys Used in Power Plants at 550 °C in CO2 Environment

High Temperature Oxidation Behavior of Co-20Re-25Cr-2Si Alloy at Different Oxygen Pressures

High-Temperature Oxidation Behavior of CrMoV, F91 and Mar-M247 Superalloys Exposed to Laboratory Air at 550 °C

Thermodynamic Analysis of Typical Alloy Oxidation and Carburization in High-Temperature CO2 Atmosphere

Oxidation Behavior of Aluminide Coatings on Cobalt-Based Superalloys by a Vapor Phase Aluminizing Process

Oxidation behavior of two austenitic steels used in 600 ℃ supercritical coal-fired power plants

Structural State of High-Entropy Fe40–xNiCoCrAlx Alloys in High-Temperature Oxidation

Cyclic and Isothermal Oxidation Behavior of a Directionally Solidified Ni-Al-Ti-Co-Cr Superalloy

Oxidation behavior at 1100 °C of NiCrAlY coatings deposited by various PVD techniques

Carbon depositions within the oxide scale and its effect on the oxidation behavior of low alloy steel in low (0.1 MPa), sub-(5 MPa) and supercritical (10 MPa) CO2 at 550°C

Oxidation behavior of 4774DD1 Ni-based single-crystal superalloy at 980 °C in air

Corrosion Behaviour of Ni-based Alloys 230, 617, and 601 in CO2 Gas at 750 and 850°C

Effect of Cyclic Reaction on Corrosion Behavior of Chromium-Containing Alloys in CO2 Gas at 650 °C

10000 Hours Thermal Aging Behavior and Supercritical CO2 Corrosion Performance of Candidate Cladding AFA Alloys for Novel Gas - Cooled Reactors

Compatibility of Different Commercial Alloys in High-Temperature, Supercritical Carbon Dioxide

Analysis of corrosion layers on protective coatings and high temperature materials in simulated service environments of modern power plants using SNMS, SIMS, SEM, TEM, RBS and X-ray diffraction studies

Effect of CO2 Gas Pressure on Composition, Growth Rate, and Structure of Duplex Oxide Formed on 9cr Steel at 550 °C

Iron oxide fluxing and precipitation in sulphate deposits during heat-resistant alloy corrosion in simulated combustion gas

Revealing the long-term oxidation and carburization mechanism of 310S SS and Alloy 800H exposed to supercritical carbon dioxide

Isothermal Oxidation Resistance of As-cast NiAl and NiAl-(Cr, Mo) Eutectic Alloys at 1000°C

Effect of Atmosphere on Duplex Oxide Formed on 9cr Steel at 550 °C