Abstract:Results on a ferritic–martensitic steel and conventional and advanced austenitic steels at 450–650°C in 30 MPa supercritical CO2 (sCO2) with and without 1% O2 and 0.1% H2O additions have indicated that carburizing sCO2 environments will have lower maximum operating temperatures compared to steam plants. Pack Al and Cr coatings were evaluated at 600o and 650°C and showed some benefit for up to 2000 h. With the addition of impurities in the sCO2, the coatings were less protective at 650°C. The carburizing supercritical CO2 (sCO2) environment limits the use of lower cost steels in the lower temperature (450–650°C) portions of the sCO2 Brayton cycle because of concerns about internal carburization and embrittlement. Results on a ferritic–martensitic steel and conventional and advanced austenitic steels at 450–650°C in 30 MPa sCO2 with and without 1% O2 and 0.1% H2O additions have indicated that sCO2 environments will have lower maximum operating temperatures compared to steam plants. Pack Al and Cr coatings were evaluated at 650°C on T91 and 316H substrates and showed some benefit for up to 2000 h at 650°C, especially without impurities. However, characterization indicated Al2O3 was not formed and Cr‐rich carbides formed in the Cr coatings. With the addition of impurities in the sCO2, the coatings were less protective at 650°C. Subsequent exposures at 600°C in sCO2 showed similar behavior. Postexposure evaluations included measuring the bulk C content and room temperature tensile properties. Improvements were indicated but the tensile results were complicated by the high temperature pack coating process affecting the substrate properties.

Temperature dependence of carbon deposits within oxide scale on CrMoV steel in atmospheric and supercritical CO2

Carbon depositions within the oxide scale and its effect on the oxidation behavior of low alloy steel in low (0.1 MPa), sub-(5 MPa) and supercritical (10 MPa) CO2 at 550°C

Revealing the Effect of O2, SO2 and H2O in Supercritical CO2 on the Corrosion Behavior of 316L Steel at Elevated Temperature

Study on Mechanical Degradation of Ferrite/ Martensite and Austenitic Steels in High-Temperature Supercritical Carbon Dioxide Environment

Effect of Supercritical CO2 on Steel Ductility at 450°-650°C

Evaluation of coated steels in supercritical CO2

Effect of surface finishing on the oxidation characteristics of a Fe-21Cr-32Ni alloy in supercritical carbon dioxide

Atomic Insights into the Corrosion Behavior of Fe-Cr Alloys in Supercritical CO2 Environment

Atomic insights into the corrosion behavior of Fe-Cr alloys in supercritical CO 2 environment.

High-Temperature Oxidation Behavior of CrMoV, F91 and Mar-M247 Superalloys Exposed to Laboratory Air at 550 °C

Corrosion and Mechanical Performance of Grade 92 Ferritic-Martensitic Steel After Exposure to Supercritical Carbon Dioxide

Effect of Impurities On the Compatibility of Steels in Supercritical CO2 at 450°-650°c

Phase Transformation Behavior Of Oxide Scale On Plain Carbon Steel Containing 0.4 Wt.% Cr During Continuous Cooling

Comparative Study On Oxidation Behavior Of Fe-5wt% Cr Alloy In Various Mixed Atmospheres At 900-1000 Degrees C

Comparative Study on Oxidation Behavior of Fe-5wt% Cr Alloy in Various Mixed Atmospheres at 900–1 000 °C

Effect of Atmosphere on Duplex Oxide Formed on 9cr Steel at 550 °C

Effect of Chromium and Water Vapor of Low Carbon Steel on Oxidation Behavior at 1050 °C

Oxidation Behavior and Lifetime Prediction of Three Commercial Alloys Used in Power Plants at 550 °C in CO2 Environment

Evolution Behavior of Carbides in 2.25Cr-1Mo-0.25v Steel

Corrosion Performance of Heat-Resisting Steels and Alloys in Supercritical Carbon Dioxide at 650 °C and 15 MPa

Structural transformation behavior of oxide scale during coiling of 0.9 wt% Cr-containing high-strength steel