Abstract:The construction of deeply buried tunnels has intensified concerns regarding shrinkage cracking and the long-term performance deterioration of lining concrete in dry-hot environments. These issues are related to the dynamic interconversion of internal moisture states, the changing moisture behavior over time, and the evolution of calcium silicate hydrate (C-S-H) properties. However, the mechanisms underlying these phenomena are not fully understood. This study investigates the dynamics of moisture content across different states, the source and composition of evaporated water, as well as the mechanism of change in the microscopic properties of C-S-H in concrete subjected to dry-hot conditions (40°C and 60°C) and standard curing environments through tests on water loss rates, chemically bound water, and low-field nuclear magnetic resonance. The findings reveal that at 40°C and 60°C, hydration products were generated rapidly before mold removal, leading to significant increases in chemically bound water, interlayer water, and gel water, while capillary water was notably consumed. After mold removal, the rate of chemically bound water increase slowed, while interlayer water, gel water, and capillary water evaporated significantly, with gel water comprising 87.27 % and 83.51 % of the evaporated water at 40°C and 60°C, respectively. From day 1 to day 28, interlayer water, gel water, and capillary water contents decreased significantly, with reductions of up to 85.98 % at 60°C. In dry-hot environments, moisture primarily exists as chemically bound water and gel water, contrasting with standard curing conditions where capillary water is also present. The study concludes that drying of C-S-H gels leads to both positive effects, such as interlayer space compression and increased indentation modulus, and negative effects, including increased microporosity and reduced matric densification, ultimately contributing to the deterioration of long-term mechanical properties.

Isothermal Drying Process and Its Effect on Compressive Strength of Concrete in Multiscale

Influence of Superplasticizer Type and Dosage on Early-age Drying Shrinkage of Cement Paste with Consideration of Pore Size Distribution and Water Loss

Influence of evaporation rate on pore size distribution, water loss, and early-age drying shrinkage of cement paste after the initial setting

Effect of Moisture Content and Porosity on Compressive Strength of Concrete During Drying at 105 °C

Effect of Different Humidity-Controlling Modes on Microstructure and Compressive Behavior of Ordinary Concrete

Influences of water by cement ratio on mechanical properties of mortars submitted to drying

Numerical Analysis of Drying Shrinkage in Long Reinforced Concrete Structure

Change of the Coefficient of Thermal Expansion of Mortar Due to Damage by Freeze Thaw Cycles

A new method for predicting compressive strength of cement-based materials

Transport properties of concrete after drying-wetting regimes to elucidate the effects of moisture content, hysteresis and microcracking

Effect of coarse aggregate size on non-uniform stress/strain and drying-induced microcracking in concrete

Investigation of drying-induced non-uniform deformation, stress, and micro-crack propagation in concrete

Effect of Temperature on Pore Structure and Strength of Concrete

Time-varying moisture characteristics and C-S-H gel properties of concrete in dry and hot environments

Moisture Sorption Behaviour, Microstructural Changes and Macroscopic Deformation of Hardened Cement Pastes During the First Three Drying–resaturation Cycles

Influence of Drying on the Stiffness and Strength of Cement-Stabilized Soils

Effect of Elevated Temperatures on Compressive Strength of Concrete

Effects of water and temperature variations on deformation of limestone aggregates, cement paste, mortar and High Performance Concrete (HPC)

Drying Shrinkage Behavior of Ultra High Toughness Cementitious Composites and Its Influence on Anti-Cracking Capacity

Effect of Cementitious Permanent Formwork on Moisture Field of Internal-Cured Concrete under Drying

Impact of Wetting and Drying Cycles on the Mechanical Properties and Microstructure of Vegetation-growing Concrete