Abstract:Ultrafiltration hollow-fiber membranes were prepared from polyetherimide (PEI) with a wet spinning method. The effects of N,N-dimethylacetantide (DMAc) as a solvent additive in the internal coagulant and acetic acid as a non-solvent additive in the dope solution on the morphologies and performances of the membranes were investigated. The influences of PEI dope concentration on membrane morphologies and properties were also studied. Scanning electron microscopy (SEM) indicates that the addition of DMAc into the internal coagulant changes the inner fiber surface from a dense skin layer to a porous structure. However, the pure water flux of the membrane decreases with the increase of DMAc content. On the other hand, the addition of acetic acid into the casting solution promotes the spinodal demixing of the membratte-forming system and suppresses the macrovoid formation in the membrane. A nodular structure forms in the fiber skin layer. With increasing acetic acid content, the pure water flux of the membrane increases about 4-fold and the solute retention shows a slight decrease. The mechanical properties can also be improved slightly by this additive. The thermal resistance of the PEI ultrafiltration membranes prepared in this work was examined by hot water treatment at 80 degrees C. No change was observed in the permeation performance of the membranes, while the study of mechanical properties shows that the elongation-at-break of the membrane decreases slightly. PEI was sulfonated by chlorosulfonic acid (CSA) in 1,2-dichloroethane. With the increase of the molar ratio of CSA to PEI repeat unit and/or reaction time, the ion-exchange capacity (IEC) of the sulfonated polyetherimide (SPEI) increases accordingly. Water uptake test and contact angle measurements show that the hydrophillicity of the SPEI increases with the increase of the IEC. Polyetherimide/sulfonated polyetherintide (PEI/SPET) ultrafiltration hollow-fiber membranes were also prepared with a dry-wet phase inversion method and SPEI was used as a polymer additive. SEM study reveals that the addition of SPEI induces the formation of nodular structure and suppresses the formation of finger-like macrovoids. With the increase of air-gap distance, it was found that the number of micropores formed in the outer fiber surface and the pore size increased. On the other hand, the pure water flux of the membrane reaches a maximum and then decreases, while the solute retention decreases at first and then levels off at longer air-gap. Based on the filtration of bovine serum albuntin (BSA) solution, it was found that the use of SPEI in the blend membranes increased their hydrophilicity.

Impact of Metal Cations on the Thermal, Mechanical, and Rheological Properties of Telechelic Sulfonated Polyetherimides

Effect Of Polyethersulfone On The Mechanical And Rheological Properties Of Polyetherimide-Modified Epoxy Systems

Poly(ethylene Oxide) Helical Conformation and Alkali Metal Cation Selectivity Studied Using Electrospray Ionization Mass Spectrometry.

Morphology and mechanical properties of poly(ether-imide)-modified polycyanurates

Facile Preparation of Halogen-Free Poly(ether Imide) Containing Phosphonium and Sulfonate Groups

Solvent Resistant Self-Crosslinked Poly(ether Imide)

New Insights in Structures, Properties, and Rheological Behaviors of Cationic Dyeable Polyesters

Sulfonated Polyetherimide And Its Membranes

Preparation and characterization of sulfonated polyetherimide/polyetherimide blend membranes

Poly(ether Imide)s with Tailored End Groups

Effect of Alkyl Side Chain Length on the Properties of Polyetherimides from Molecular Simulation Combined with Experimental Results

Thermally Driven Ionic Aggregation in Poly(ethylene Oxide)-Based Sulfonate Ionomers.

Effect of anion size and salt concentration on ion transport in PEO-based solid polymer electrolytes at high temperatures

Effect of Degree of Neutralization on the Properties of Ionic Thermoplastic Elastomer Based on Sulfonated Maleated Styrene-Ethylene/Butylene-Styrene Block Copolymer

Multi-Length Scale Morphology Of Poly(Ethylene Oxide)-Based Sulfonate Ionomers With Alkali Cations At Room Temperature

Modification of Polyetherimide by Phenylethynyl Terminated Agent for Improved Tribological, Macro- and Micro-Mechanical Properties

Preparation And Performance Of Ultrafiltration Membranes From Polyetherimide And Its Sulfonated Derivatives

Synthesis and comparative study of thermoplastic polyetherimides derived from hydroquinone diphthalic anhydride isomers with tert -butyl group

Metal Composition and Polyethylenimine Doping Capacity Effects on Semiconducting Metal Oxide-Polymer Blend Charge Transport.

Novel Soluble Fluorinated Poly(Ether Imide)S with Different Pendant Groups: Synthesis, Thermal, Dielectric, and Optical Properties

Characterization and properties of sPS/PET/SsPS-K engineering plastic alloys