Abstract:Ultrafiltration hollow-fiber membranes were prepared from polyetherimide (PEI) with a wet spinning method. The effects of N,N-dimethylacetantide (DMAc) as a solvent additive in the internal coagulant and acetic acid as a non-solvent additive in the dope solution on the morphologies and performances of the membranes were investigated. The influences of PEI dope concentration on membrane morphologies and properties were also studied. Scanning electron microscopy (SEM) indicates that the addition of DMAc into the internal coagulant changes the inner fiber surface from a dense skin layer to a porous structure. However, the pure water flux of the membrane decreases with the increase of DMAc content. On the other hand, the addition of acetic acid into the casting solution promotes the spinodal demixing of the membratte-forming system and suppresses the macrovoid formation in the membrane. A nodular structure forms in the fiber skin layer. With increasing acetic acid content, the pure water flux of the membrane increases about 4-fold and the solute retention shows a slight decrease. The mechanical properties can also be improved slightly by this additive. The thermal resistance of the PEI ultrafiltration membranes prepared in this work was examined by hot water treatment at 80 degrees C. No change was observed in the permeation performance of the membranes, while the study of mechanical properties shows that the elongation-at-break of the membrane decreases slightly. PEI was sulfonated by chlorosulfonic acid (CSA) in 1,2-dichloroethane. With the increase of the molar ratio of CSA to PEI repeat unit and/or reaction time, the ion-exchange capacity (IEC) of the sulfonated polyetherimide (SPEI) increases accordingly. Water uptake test and contact angle measurements show that the hydrophillicity of the SPEI increases with the increase of the IEC. Polyetherimide/sulfonated polyetherintide (PEI/SPET) ultrafiltration hollow-fiber membranes were also prepared with a dry-wet phase inversion method and SPEI was used as a polymer additive. SEM study reveals that the addition of SPEI induces the formation of nodular structure and suppresses the formation of finger-like macrovoids. With the increase of air-gap distance, it was found that the number of micropores formed in the outer fiber surface and the pore size increased. On the other hand, the pure water flux of the membrane reaches a maximum and then decreases, while the solute retention decreases at first and then levels off at longer air-gap. Based on the filtration of bovine serum albuntin (BSA) solution, it was found that the use of SPEI in the blend membranes increased their hydrophilicity.

Sulfonated Polyetherimide And Its Membranes

Preparation and characterization of sulfonated polyetherimide/polyetherimide blend membranes

Sulfonated Polyaryletherketone with Pendant Benzimidazole Groups for Proton Exchange Membranes

Preparation And Performance Of Ultrafiltration Membranes From Polyetherimide And Its Sulfonated Derivatives

Preparation of High Density Polyethylene/polyethylene- Block -Poly(ethylene Glycol) Copolymer Blend Porous Membranes Via Thermally Induced Phase Separation Process and Their Properties

Solvent Resistant Self-Crosslinked Poly(ether Imide)

Ultrafiltration Hollow Fiber Membranes of Sulfonated Polyetherimide/polyetherimide Blends: Preparation, Morphologies and Anti-Fouling Properties

Synthesis and Characterization of Sulfonated Poly(arylene Ether Ketone/ketone Phosphine Oxide)s As Proton Exchange Membranes

Ultrafiltration Hollow Fiber Membranes from Poly(Ether Imide): Preparation, Morphologies and Properties

Impact of Metal Cations on the Thermal, Mechanical, and Rheological Properties of Telechelic Sulfonated Polyetherimides

PREPARATION AND PROPERTIES OF SULFONATED POLY(ARYLENE ETHER SULFONE)/SULFONATED POLYIMIDE BLEND PROTON EXCHANGE MEMBRANES

Study on polyetherimide hollow fiber ultrafiltration membrane (Ⅰ) Membrane structure, thermal and mechanical properties

Novel Composite Anion Exchange Membranes Based on Quaternized Polyepichlorohydrin for Electromembrane Application

Facile Preparation of Halogen-Free Poly(ether Imide) Containing Phosphonium and Sulfonate Groups

Novel Sulfonated Polyimides Proton-Exchange Membranes Via a Facile Polyacylation Approach of Imide Monomers

Preparation of Hyperbranched Polyethyleneimine Composite Membrane Using Interfacial Polymerization Catalyzed by 4-Dimethylamiopryidine

Synthesis and Properties of Sulfonated Poly(arylene Ether Phosphine Oxide)s for Proton Exchange Membranes

Synthesis and Characterization of Sulfonated Poly(aryl Ether Sulfone) Containing Pendent Quaternary Ammonium Groups for Proton Exchange Membranes

STUDY ON THE PREPARATION AND PROPERTIES OF SULFONATED PHENOLPHTHALEIN POLY(ETHER SULFONE) MEMBRANES

Polymeric asymmetric membranes made from polyetherimide/polybenzimidazole/poly(ethylene glycol) (PEI/PBI/PEG) for oil–surfactant–water separation

Micromechanism Study of Molecular Compatibility of PVDF/PEI Blend Membrane