Abstract:<p>For wear resistant steels, there is generally a linear relationship between the initial hardness and wear resistance, yet a high initial hardness limits the formability of components. The intrinsic ductility of austenite and strain hardening produced from the transformation-induced plasticity (TRIP) effect during service opens a new window for this contradiction. Herein, the wear resistance and the corresponding failure mechanisms of 5Mn steels after different heat treatment processes were evaluated using a ball-on-disk sliding test under dry conditions. The wear behaviors of the counterbodies were also studied to elucidate the wear mechanism of the tribo-system. The results show that the microstructures of the hot-rolled and air-cooled steel mainly comprised martensite. When the intercritical annealing temperature was relatively low (<695°C), the microstructure primarily consisted of reversed austenite and ferrite. The samples annealed at 630°C, 645°C, 660°C, and 675°C had a similar initial hardness, while the sample annealed at 675°C possessed a wear resistance that was 3.25 times that of the steel annealed at 630°C. The large difference in the wear resistance was predominately due to the gradient of strain hardening provided by the varied amount and mechanical stability of the retained austenite. The transformation from austenite to martensite, which has an increased hardness, improves the work hardening. A strengthening layer formed with a certain thickness that provided stress support during the wear process and enhanced the wear resistance. When the annealing temperature reached 695°C, a large amount of secondary martensite was generated from austenite that had a low thermal stability, which improved the initial hardness and wear resistance. The steels with a large amount of martensite had an enhanced wear resistance, but the elongation severely deteriorated, leading to unsatisfactory formability. The present work provides guidance for designing novel steels with an excellent balance of good formability and decent wear resistance by precisely adjusting the characteristics of the retained austenite.</p>

Effect of Matrix Structure on Mechanical Properties and Dry Rolling–sliding Wear Performance of Alloyed Ductile Iron

Analysis on Wear Properties and Impact Factors for Si3N4 Ceramic Mated with Chilled Cast Iron

Sliding wear behaviour of austempered ductile iron, boron steel and AISI 1045 steel of similar hardness: effect of microstructure, yield strength, and strain hardening

Mechanical and tribological behavior of dual-phase ductile iron with different martensite amounts

Effect of Hot-Rolling Deformation on Microstructure and Sliding Wear of High-Chromium Cast Iron

Effect of Surface Melting and Chromium Surface Alloying on Wear Behavior of Ductile Iron

Dry sliding wear of MA/PM Al-10Ti alloy

Microstructure, Mechanical, and Wear Properties of Al-Alloyed Austempered Ductile Irons

New insight into the dry rolling-sliding wear mechanism of carbide-free bainitic and pearlitic steel

Effect of layered heterogeneous microstructure design on the mechanical behavior of medium carbon steel

Unraveling the significant role of retained austenite on the dry sliding wear behavior of medium manganese steel

Research on Effects of Rolling-Drawing Deformation on Performance of Cu-10Ni-1Fe-1Mn Alloy

Microstructures, Compressive Residual Stress, Friction Behavior, and Wear Mechanism of Intensive Quenched Ductile Iron

Effect of hardenability on microstructure and property of low alloy abrasion-resistant steel

Influence of Materials on Dry Friction and Wear Performance of Harmonic Reducer Circular Spline

Effect of Aluminum, Copper and Manganese on the Structure and Properties of Cast Irons

Effect of hot rolling on microstructure and tribology behaviors of Ti−50.8Ni alloy

Effect of Heat Treatment on the Frictional Wear Properties of Zr-Based Amorphous Alloy

On the Morphology Variation of Graphite in Ductile Cast Iron through Severe Plastic Deformation

Effects of Different Forging Ratios on Microstructure, Mechanical Properties and Friction and Wear Behavior of Q355D Steel

Effect of alloying elements W, Ti, Sn on microstructure and mechanical properties of gray iron 220