Abstract:The ta-C films were fabricated using direct-current cathodic arc evaporation (DC-CAE) and pulse-enhanced cathodic arc evaporation (PE-CAE). The effect of peak currents (I-p) on arc discharge, microstructure and mechanical properties of the films was focused on. The enhanced discharge process, microstructure and mechanical properties of the ta-C films were investigated by means of optical emission spectra (OES), Raman spectroscopy, Nano-indentation, etc. With the same average current, the I-p of 300 A of PE-CAE produced the substrate current of 1.14 A, but a markedly low current (0.82A) was observed for the DC-CAE. The plasma emission intensity of Ar II, C I and C II also increased by about 86%, 66% and 630% at pulse mode. This evidently indicated an enhanced arc discharge by PE-CAE. The highest ratio of CII/ArII (2.98) and electron excitation temperature (1.38 eV) was observed. DC-CAE led to a lower concentration of sp(3) bonding (47.3%, I-D/I-G = 0.39) of ta-C films with a thickness of 171 nm. In contrast, the ta-C films fabricated by PE-CAE (I-p = 300 A) possessed the smallest I-D/I-G (0.22) as well as the highest concentration of sp(3) bonding (65.1%). The thickness increased by about 30% in comparison with that by DC-CAE. The largest thickness (330 nm) was obtained at the peak current of 200A, mainly relating to the increased evaporation of carbon atom/ions. The hardness evaluated from the ta-C films fabricated by DC-CAE was about 29 GPa. However, the hardness increased significantly to 57 GPa by PE-CAE (I-p = 300 A), and the preferable toughness (H/E* of 0.11 and H-3/E*(2) of 0.68) was simultaneously achieved.

Microstructure and Mechanical Properties of Ta-C Films by Pulse-Enhanced Cathodic Arc Evaporation: Effect of Pulsed Current

Enhancement of Discharge and Deposition Rate by Imposed Pulse Current During the Cathodic Arc Deposition of Ta-C Films

Structure and properties of ta-C films prepared by vacuum cathodic arc with an unbalanced external electromagnetic field

Microstructure evolution and mechanical properties of Al doped ta-C films prepared by filtered cathodic vacuum arc

Strongly Adhering and Thick Highly Tetrahedral Amorphous Carbon (ta–c) Thin Films Via Surface Modification by Implantation

Microstructure and tribological behavior in ta-C films prepared by laser-induced filtered cathodic vacuum arc technique: Effect of charge voltage

Influence of Ion Energy and Substrate Temperature on the Optical and Electronic Properties of Tetrahedral Amorphous Carbon (Ta-C) Films

Structure and Properties of Ta-C Films Deposited by Filtered Cathodic Vacuum Arc Technology As a Function of Substrate Bias

Structure, mechanical and tribological properties, and oxidation resistance of TaC/a-C:H films deposited by high power impulse magnetron sputtering

Microstructure, adhesion, mechanical and corrosion properties of TiN coatings deposited by high energy pulse-enhanced vacuum arc evaporation

Structure and Tribological Properties of Ultra-Thin Tetrahedral Amorphous Carbon (ta-C) Films

Field emission properties from aligned carbon nanotube films with tetrahedral amorphous carbon coatings

Tribological Properties of Ta‐C‐N and Ta‐N Thin Films

Electronic Properties of Tetrahedral Amorphous Carbon (Ta-C) Films Containing Nanotube Regions

Highly Tetrahedral Amorphous Carbon Films with Low Stress

Effect of TaC Content on Microstructure and Properties of W-TaC Composites

Ablation behavior of Ta, TaC and Ta/TaC coatings on graphite under high-energy laser irradiation

Stress, Microstructure and Mechanical Properties of Graded Multilayer Tetrahedral Amorphous Carbon Films

Microstructure and Tribological Properties of Ti-contained Amorphous Carbon Film Deposited by DC Magnetron Sputtering

Controlling microstructure, preferred orientation, and mechanical properties of Cr-Al-N by bombardment and alloying with Ta

TaCN Growth with PDMAT and H2/Ar Plasma by Plasma Enhanced Atomic Layer Deposition