Abstract:The mechanical properties of metallic matrix composites can be tailored through the microstructural modification between metal matrix and reinforcing particles. In this work, the AA2219/TiC nanocomposite containing 0, 0.5, 0.9, 1.3 and 1.7 wt.% TiC nanoparticles were individually manufactured using the ultrasound-assisted solidification technique. There existed an optimal addition level of TiC nanoparticles (0.9 wt.%) beyond which grain coarsening occurred. TiC nanoparticles were observed to reduce the average grain sizes of α-Al matrix alloy by 61%. Meanwhile, 0.9 wt.% TiC nanoparticles corresponded to the maximum tensile strength and hardness. When the addition level reached over 0.9 wt.% in the 2219 Al alloy matrix melt, the TiC nanoparticles tended to agglomerate in a form of condensed clusters, which cannot be well dispersed by ultrasonication due to the increasing viscosity. Such agglomerating TiC nanoparticles deteriorated the tensile strain and hardness of AA2219/TiC nanocomposite. Then, five major potential strengthening mechanisms in AA2219/TiC nanocomposite was quantitatively analysed, including grain refinement, Orowan strengthening, load transfer effect, mismatch of thermal expansion, and mismatch of elastic modulus. Analysis shows that Orowan strengthening acts as the most dominant strengthening mechanism, followed by another comparable strengthening mechanism from the mismatch between the thermal expansion of α-Al matrix and TiC nanoparticles. The other three strengthening mechanisms induced very limited improvement in mechanical properties. Besides acting as reinforcing agents, the TiC nanoparticles also possess very high potency as heterogeneous nucleation sites. The relevant nucleation potency was validated by crystallographic investigation using the edge-to-edge matching model. Finally, the grain refining mechanism of α-Al matrix alloy was unraveled in terms of the nucleation crystallography and the ultrasonic cavitation.

High-temperature Mechanical Properties of 2024 Al Matrix Nanocomposite Reinforced by TiC Network Architecture

High Temperature Tensile Properties of in Situ TiBw/Ti6Al4V Composites with a Novel Network Reinforcement Architecture

Microstructure and mechanical behaviors of Ti<sub>3</sub>AlC<sub>2</sub> triggered in-situ Al<sub>3</sub>Ti and TiC reinforced 2024Al composite

Investigation on Particle Strengthening Effect in In-Situ TiB2/2024 Composite by Nanoindentation Test

Hierarchically heterogeneous strategy for Ti 2 AlC/TiAl composite with superior mechanical properties

Microstructure characterization and enhanced mechanical properties of quasi-continuous network structured Ti3AlC2-Al3Ti/2024Al composite

Enhancing the High-Temperature Mechanical Property and Microstructure Stability in Ti-4822 Matrix Composites Via Ti/Al Transition Layer

Construction of Three-Dimensional Network Morphology Titanium Matrix Composites Via Adding Nano B4C: As-built and Heat-Treated Scenarios

Design, microstructure and high temperature properties of in-situ Al3Ti and nano-Al2O3 reinforced 2024Al matrix composites from Al-TiO2 system

Simultaneous Improvement in Strength and Ductility of TC4 Matrix Composites Reinforced with Ti1400 Alloy and In Situ-Synthesized TiC

Fabrication, microstructure and mechanical properties of TiAl matrix composite reinforced by submicro/nano-Ti 2 AlC

In Situ Ti2AlN Reinforced TiAl-based Composite with a Novel Network Structure: Microstructure and Flexural Property at Elevated Temperatures

The nano-sized TiC particle reinforced Al–Cu matrix composite with superior tensile ductility

Microstructures and Mechanical Properties of TiAl Matrix Composites with Multi-Precipitates Quasi-Continuous Network Reinforced Structures

An Investigation of Microstructural Evolution, Tensile Properties and Work-Hardening Behavior of Nanosized TiB2/Al-Cu-Mn Composites

High-temperature Mechanical Properties and Strengthening Mechanism of In-situ (TiB+ TiC)/Ti-1100 Composite

Network-Strengthened Ti-6Al-4V/(TiC+TiB) Composites: Powder Metallurgy Processing and Enhanced Tensile Properties at Elevated Temperatures

Effect of Nanoparticle Content on the Microstructural and Mechanical Properties of Forged and Heat-Treated TiC/2219 Nanocomposites

Simultaneously Increasing the High-Temperature Tensile Strength and Ductility of Nano-Sized TiCp Reinforced Al-Cu Matrix Composites

Microstructural evolution and mechanical properties of the AA2219/TiC nanocomposite manufactured by ultrasonic solidification

Fabrication of Aluminum Matrix Composite Reinforced with Carbon Nanotubes