Abstract:The basic structure of an organic light emitting device (OLED) is composed of a hole trans porting layer (HTL). a light-emitting layer, an electron transporting layer (ETL) , sandwiched between the anode and cathode. The operating mechanisms of the OLEDs involve the injection of electrons and holes from the electrodes, and electron-hole recombination which emits the light. Therefore, the efficiency of the carrier injecting has a great influence on the performance of the device. A variety of materials for both the anode and cathode, which has recently attracted strong attention is systematically studied, The mechanisms of the improvement of several anode treatments and a popular cathode structure are especially analyzed. For anode, a transparent and conducting thin film which is usually oxide can be adopted. And because the barrier height of the anode and the HTL decides the efficiency of the hole injecting, the maten al used as anode should also attain a high work function. Then indium-tin-oxide (ITO) is a better choice and has been used more widely, compared with other materials. The work function of ITO thin film can be increased after oxygen-plasma, ultraviolet(UV) ozone, and aquaregia treatments. The reason is discussed of that, and consider that although three factors i.e.:. (1) C-containing contaminants, (ii) the O/In ratio, and (iii) the In/Sn ratio on the surface affect the work function, the first one is crucial. For a good treatment, the variation of the resistivity of ITO after it should also be taken into account, because a low volt age share of the anode would result in the reduction of the turn-on voltage. Similar to the hole injecting, the barrier height of the cathode and the ETL decides the efficiency of the electron injecting. But contrary to the anode, a low work function is preferable for the material as cathode. And a good chemical stability in air is also expected. Now the cathode with a structure metal/thin insulating layer maybe the idealest choice. Explanations have been put forward for the remarkable improvement of the special structure from several aspects i. e. : (i) tunneling effect, (ii) valence band bending, (iii) reduction of the quenching cen ters. and (iv) dipole mode. Through analysis, the first three aspects are more reasonable, and they are all responsible for the improvement, but with different contribution.

The Visible and Ultraviolet Organic Light-Emitting Diodes with Germanium Dioxide As Facile Solution-Processed Anode Buffer Layer

Al2O3 Buffer Layers and Characteristics of Organic Light Emitting Devices Made of Al-Doped ZnO Films

Performance Improvement of Organic Light Emitting Diode with Aluminum Oxide Buffer Layer for Anode Modification

Organic light-emitting devices with a 2-(4-biphenyl)-5-(4-butylphenyl)-1,3,4-oxadiazole layer between the α-naphtylphenyliphenyl diamine and 8-hydroxyquinoline aluminum

Efficient Single-Active-Layer Organic Light-Emitting Diodes With Fluoropolymer Buffer Layers

Organic Light-Emiting Diodes with a Bilayer Electrode

Electro-optical performance of molybdenum oxide modified aluminum doped zinc oxide anodes in organic light emitting diodes: A comparison to indium tin oxide

Highly Efficient Simplified Organic Light-Emitting Diodes Utilizing F4-TCNQ As an Anode Buffer Layer

Experimental study of the organic light emitting diode with a p-type silicon anode

Obvious Efficiency Enhancement of Organic Light-Emitting Diodes by Parylene-N Buffer Layer

Solution-processed Cathode-Interlayer-free Deep Blue Organic Light-Emitting Diodes

Efficient organic light-emitting diodes with teflon as buffer layer

Blue organic light-emitting diodes with low driving voltage and maximum enhanced power efficiency based on buffer layer MoO3

Luminescent Organogermane Emitter with Folded Conformation for Operationally Stable Blue Organic Light-Emitting Diode

Effect of Nacl Buffer Layer on the Performance of Organic Light-Emitting Devices (Oleds)

Novel Solution-Processed ZnO-Based Electron Injection Layer for Organic Light-Emitting Diodes

Enhancement of hole injection with an ultra-thin Ag2O modified anode in organic light-emitting diodes

Aluminum-Doped Zinc Oxide Transparent Electrode Prepared by Atomic Layer Deposition for Organic Light Emitting Devices

The Study of Electrodes for Organic Electroluminescent Devices

Enhanced Brightness and Efficiency in Organic Light-Emitting Diodes Using SiO2 As Buffer Layer and Electron-Blocking Layer

Applications of Transparent Conducting Oxides in Organic Light Emitting Devices.