Abstract:High-reflectance ohmic contacts to p-GaN are the key for Flip-chip ultra-violet light emitting diode (UV-LED) to improve the external quantum efficiency (EQE), so the kinds of metal or alloy film both ohmic contact and the reflector of light are important to choose the appropriate high-reflectance and low-resistance ohmic contact to p-type GaN. The GaN-based LED samples used were grown by Metalorganic Chemical Vapor Deposition (MOCVD). Four different metal films were deposited on the surfaces of p-GaN and annealed Ni/Au alloy. The thickness of these metal films varied from 30 nm to 840 nm. The reflectance and transmittance of the samples were mea- sured by WGS-9 system. The 2θ scans XRD and surface AFM images of the samples were also observed. As results, when the films' thickness under the 130 nm the reflectance of Ag-deposited samples increased with the increasing thickness and the transmittance decreased at wavelength of 400 nm. The reason of the increasing of reflectance is the reduction of the light transmitted through the films. When the films' thickness over 130 nm, the reflectance of Ag-deposited samples decreasing. From the results of XRD and AFM, the metal film formed multi-layers film and the roughness R_a and R_q increased with the increasing thickness. It is suggested that the diffusion of the multi-layers films is the main reason of reduction of reflectance with the films thickness increasing. Other metal films show the same characteristics as the Ag-deposited films. From the result of reflectance, Al and Ag are the suitable candidates for the reflector, but it is reported that the single Al or Ag films don't make good ohmic contacts on p-GaN. So a thin annealed Ni/Au is adopted to interspersed between the Al or Ag reflector and the p-GaN in order to provide efficient hole injection into the device. From the results of reflectance and I-V curves of Ni/Au/Ag and Ni/Au/Al, the I-V characteristics of Ni/Au/Ag and Ni/Au/Al contacts are similar to this of Ni/Au annealed. However the reflectance of Ni/Au/Ag and Ni/Au/Al contacts is three times higher than that of Ni/Au at wavelength of 400 nm. These results demonstrated that Ni/Au/Ag and Ni/Au/Al can be used as high-reflectance and low-resistance p-GaN ohmic contacts for flip-chip UV-LEDs

High-stability Reflective Bonding Pads for GaN-based Flip-Chip Light-Emitting Diodes Packaged by Reflow Soldering

Effects of Bonding Materials on Optical–Thermal Performances and High-Temperature Reliability of High-Power LED

Ohmic Contact of High Reflectivity on P-Type GaN

Thermal Analysis of Flip-Chip Bonding Designs for GaN Power HEMTs with an On-Chip Heat-Spreading Layer

High-output power GaN-LED based on surface plasmon enhancement

A Novel Strategy for GaN-on-Diamond Device with a High Thermal Boundary Conductance

Vertical Electrode Structure GaN Based Light Emitting Diodes

High-reflectance Ohmic Contacts to P-Gan of GaN-based Violet LEDs

Thermal Dispersion of GaN-based Power LEDs

Study on Light Extraction Efficiency of GaN-based Light-emitting Diode Chips

Phase Reaction of Au/Sn Solder Bonding for GaN-based Vertical Structure Light Emitting Diodes

Wafer-scale bonded GaN–AlN with high interface thermal conductance

High Performance Gallium Nitride Based Blue Light Emitting Diode Material Epitaxy and Dry Etching Fabrication Technology

Reduced thermal boundary conductance in GaN-based electronic devices introduced by metal bonding layer

Study of laser-debonded GaN light emitting diodes

High-Power GaN-Based Vertical Light-Emitting Diodes on 4-Inch Silicon Substrate

Study of GaN Light-Emitting Diodes Obtained by Laser-Assisted Debonding

Ni/Ag Reflector Electrode of GaN-Based Vertical LED

Enhancement of Extraction Efficiency in Laser-debonded GaN Light Emitting Diodes

Improved Reliability of AlGaN-Based Deep Ultraviolet LED With Modified Reflective N-Type Electrode

The Influences of Sputtered AlN Buffer Layer on AlInGaN Based Blue and Near‐ultraviolet Light Emitting Diodes