Abstract:In this paper, Zr, Cr and V were selected as the partial substitution elements for Ti to form Mg35Ti5M5Ni55 quaternary alloys prepared by means of mechanical alloying on the basis of the ternary Mg35Ti10Ni55 electrode alloy previously studied by the authors. It is found that all the three quaternary alloys possess an amorphous main phase and exhibit improved cycling stability than the original ternary Mg35Ti10Ni55. The Zr-substituted alloy has also a higher discharge capacity. X-ray photoelectron spectroscopy (XPS) surface analysis reveals that on the surface of each alloy a multi-component oxide composite film is formed, which is more compact and corrosion resistant than the Mg(OH)2 film and the (TiO2)x(NiO)y(Mg(OH)2)z composite films reported previously. Auger electron spectroscopy (AES) analysis shows that the substituting elements tend to reduce the thickness of the passivation films. The thickness of composite oxide film on the alloys is in the following order: Mg35Ti10Ni55>Mg35Ti5V5Ni55>Mg35Ti5Zr5Ni55>Mg35Ti5Cr5Ni55. The result agrees well with that of the polarization resistances (RP) values obtained from the electrochemical impedance spectroscopy (EIS) Nyquist diagrams. It demonstrates that the thicker the passivation film is, the higher the RP is and the more difficultly the charge transfer reaction proceeds. Anodic polarization curves indicate that the addition of Cr and Zr decreases effectively the corrosion current. However, the corrosion of the electrode alloys in the electrolyte is still high and proceeds constantly as the corrosion current remains almost constant during further cycles.

Effects of Grain Size and Secondary Phase on Corrosion Behavior and Electrochemical Performance of Mg-3Al-5Pb-1Ga-Y Sacrificial Anode

Effects of Grain Size on the Corrosion and Discharge Behaviors of Mg–Y Binary Alloys for Mg-Air Batteries

Effect of grain size and crystal orientation on the corrosion behavior of as-extruded Mg-6Gd-2Y-0.2Zr alloy

The Effect of Extrusion Ratio on the Discharge and Corrosion Behavior of Mg-3Al-2.8Y-0.7Mn Alloy

Effects of Alloying Elements on the Corrosion Behavior and Discharge Performance of Al-Zn-Mg-In-Ti-Sn Sacrificial Anode

The effect of partial substitution of Ti with Zr, Cr or V in the Mg35Ti10Ni55 electrode alloy on its electrochemical performance

Establishment of electrode potential-composition plot of Al-Mg-Zn alloys and sacrificial anode protection tests

The effects of mechanical grinding on the hydrogen storage properties of MlNi4.7Al0.3 alloy

Effect of Microstructure on the Corrosion Behavior of as-cast and Extruded Mg–Sn–Y Alloys

The electrochemical corrosion behaviors and Mg-air battery anode performance of Mg–1Sn–1Ca-0.3Mn alloy with different grain size and Mg 2 Ca morphology

Electrochemical Performance of Al-Mg Based Sacrificial Anodes

Improving the electrochemical behaviors and discharge performance of as-rolled Mg-4Li alloys through multicomponent alloying

Effect of grain size uniformity and crystallographic orientation on the corrosion behavior of Mg-2Zn-1Al bar

Effects of grain size and Al-Mn phase on the corrosion performance of hot-rolled AZ31 magnesium alloy

New insights on corrosion behavior of aging precipitates in dilute Mg-Al-Ca alloy by experiments and first-principles calculations

Effects of Zn/Ca alloying on the Second Phase, Corrosion Behavior and Mg‐air Battery Anodic Performance of Mg‐1Sn‐based Alloys

Comparative Study on Corrosion Behavior and Mechanism of As-Cast Mg–Zn–Y and Mg–Zn–Gd Alloys

Tailoring the electrochemical behavior and discharge performance of Mg–Al–Ca–Mn anodes for Mg-air batteries by different extrusion ratios

Comparison of the Corrosion Behaviors of Mg–Gd–Y–Zn–Zr Alloys Fabricated by Different Preparation Methods

The effect of grain size and grain boundary misorientation on the corrosion resistance of commercially pure aluminium

Microstructure evolution and corrosion properties of ECAPed Mg–Pb-9.2Al-0.8B alloys