Abstract:Theprecipitate behavior, mechanical properties and corrosion behavior of an Al-Zn-Mg-Cu alloy during non-isothermal creep aging were investigated. The results show that diffraction patterns of GPI zones gradually disappear and those of η′ phases are strengthened during the heating stage. More importantly, the size and volume fraction of precipitates increase with aging temperature increasing, which greatly enhances the mechanical properties of the alloy. The hardness and tensile strength of the alloy with H210 aging condition are 165 HV and 564 MPa, respectively. During the cooling stage, in addition to the diffraction pattern of η′ phase, that of GPI zones can be observed again. Furthermore, the size of the precipitates decreases, and the volume fraction reaches a maximum. The hardness and tensile strength of the alloy with C120 aging condition reach 185 HV and 580 MPa, respectively. Furthermore, the characteristics of the grain boundary reveal that the width of precipitation free zones (PFZ) first increases during the heating stage and then decreases during the cooling stage. In the C120 condition, the newly generated secondary precipitates and the coarsening of undissolved precipitates around the grain boundary lead to the further narrowing of PFZ, but the coarse grain boundary precipitates (GBPs) are still not continuously distributed in the grain boundary. Hence, the alloy with C120 condition exhibits the most excellent corrosion resistance.

New insights on corrosion behavior of aging precipitates in dilute Mg-Al-Ca alloy by experiments and first-principles calculations

Atomic-scale study on the precipitation behavior of an Al-Zn-Mg-Cu alloy during isochronal aging

Initial localized corrosion induced by multiscale precipitates in the new generation high-strength Al-Zn-Mg-Cu alloy

Role of alloyed Al on the microstructure and corrosion behavior of as-cast dilute Mg-2Zn- x Al-0.5Ca alloys

Formation of amorphous precipitates in a corroded over-aged Al-Mg-Si alloy

Effect of Ca Micro-Alloying on the Microstructure and Anti-Corrosion Property of Mg0.5Zn0.2Ge Alloy

Improving Aging Behavior and Corrosion Resistance of Mg-5Ga Alloy by Ca Alloying

Enhancing corrosion resistance of ZK60 magnesium alloys via Ca microalloying: The impact of nanoscale precipitates

Effects of Mg/Zn ratio and pre-aging on microstructure and mechanical properties of Al–Mg–Zn–Cu alloys

Precipitate Behavior, Mechanical Properties and Corrosion Behavior of an Al-Zn-Mg-Cu Alloy during Non-Isothermal Creep Aging with Axial Tension Stress

Investigating the corrosion behavior of as‐cast Mg‐Zn‐Ca alloys with the same Zn/Ca atomic ratio by in situ observation

Effects of micro-alloying Ag on microstructure, mechanical properties and corrosion behavior of extruded Mg-2Zn-0.2Ca-xAg alloys

Influence of Minor Zn Addition on Precipitation Behavior and Intergranular Corrosion Properties of Al-Mg-Si Alloy

Microstructure and corrosion properties of Mg–0.5Zn–0.2Ca–0.2Ce alloy with different processing conditions

Influence of Mg content on ageing precipitation behavior of Al-Cu-Li-x alloys

Synchronous improvement in mechanical properties and corrosion resistance of Mg-Gd-Ag-Zr alloy through nanoprecipitates

Microstructure evolution and corrosion properties of ECAPed Mg–Pb-9.2Al-0.8B alloys

Microstructure, Mechanical Properties, and Corrosion Behavior of Al-4.0Cu-1.1Li-0.5Mg-xAg Alloys

Elucidating the dependence of corrosion behavior and mechanical property on the grain structure of low-temperature as-extruded Mg–Zn–Ca–Zr alloy

Regulating corrosion resistance of Mg alloys via promoting precipitation with trace Zr alloying

Study on Microstructural Evolution and GP Zone Strengthening Mechanism by Solution and Aging Treatment in Non-dendritic Mg-6Zn-5Al Magnesium Alloy