Abstract:Magnesium-Zinc-Zirconium (Mg-Zn-Zr) alloys have caught considerable attention in medical applications where biodegradability is critical. The combination of their good biocompatibility, improved strength, and low cytotoxicity makes them great candidates for medical implants. This research investigation is focused on providing further insight into the effects of equal channel angular processing (ECAP) on the corrosion behavior, microstructure evolution, and mechanical properties of a biodegradable ZK30 alloy. Billets of Mg-3Zn-0.6 Zr (ZK30) alloy were processed through ECAP up to 4 passes of route Bc (rotating the billets 90° in the same direction between the subsequent passes) at 250 °C. Electron back-scatter diffraction (EBSD) was utilized to investigate the microstructural evolution as well as the crystallographic texture. Several electrochemical measurements were carried out on both a simulated body fluid and a 3.5% sodium chloride (NaCl) solution. Mechanical properties such as Vicker's hardness and tensile properties were also assessed. The as-annealed (AA) microstructure was dominated by equiaxed coarse recrystallized grains with an average grain size of 26.69 μm. After processing, a geometric grain subdivision took place due to the severe plastic deformation. Processed samples were characterized by grain refinement and high density of substructures. The 4-passes sample experienced a reduction in the grain size by 92.8% compared with its AA counterpart. The fraction of high-angle grain boundaries increased significantly after 4-passes compared to the 1-pass processed sample. With regards to the crystallographic texture, the AA condition had its {0001} basal planes mostly oriented parallel to the transversal direction. On the other hand, ECAP processing resulted in crystallographic texture changes, such as the shifting of the ZK30 shear plane to be aligned at 45° relative to the extrusion direction (ED). Furthermore, the maximum texture intensity was reduced from 14 times random (AA billets) to 8 times random after ECAP processing through 4-passes. The corrosion rate of the 4-passes sample was tremendously reduced by 99% and 45.25% compared with its AA counterpart in the simulated body fluid and the NaCl solution, respectively. The pitting corrosion resistance of ZK30 showed notable improvements in the simulated body fluid by 471.66% and 352% during processing through 1-pass and 4-passes, respectively, compared with the 3.5% NaCl findings. Finally, significant improvements in the tensile strength, hardness, and ductility were also achieved.

Microstructure evolution and corrosion properties of ECAPed Mg–Pb-9.2Al-0.8B alloys

The Effects of ECAP, Mn and Ca Elements on the Microstructure and Corrosion Properties of Magnesium Alloys Were Investigated

Microstructural homogeneity, texture and corrosion properties of RE-doped 55Mg-35Pb-9.2Al-0.8B alloy fabricated via equal channel angular pressing (ECAP)

Effects of Zn Addition on Microstructural Evolution, Mechanical Properties and Corrosion Resistance of Al-6Mg Alloy Subjected to ECAP Processing at 200 ℃

Anisotropy investigation of an ECAP-processed Mg-Al-Ca-Mn alloy with synergistically enhanced mechanical properties and corrosion resistance

Effect of ECAP on the microstructure and mechanical properties of Zn-0.5Ag-0.08Mg alloy

Microstructural evolution and mechanical response of duplex Mg-Li alloy containing particles during ECAP processing

Improving In-Vitro Corrosion and Degradation Performance of Mg–Zn–Ca Alloy for Biomedical Applications by Equal Channel Angular Pressing

Influence of Ultrafine-Grained Microstructure and Texture Evolution of ECAPed ZK30 Magnesium Alloy on the Corrosion Behavior in Different Corrosive Agents

Influence of ECAP as grain refinement technique on microstructure evolution, mechanical properties and corrosion behavior of pure aluminum

In vitro study on equal channel angular pressing AZ31 magnesium alloy with and without back pressure

Regulating hardness homogeneity and corrosion resistance of Al-Zn-Mg-Cu alloy via ECAP combined with inter-pass aging

Effect of ECAP Processing on Corrosion Behavior and Mechanical Properties of the ZFW MP Magnesium Alloy as a Biodegradable Implant Material

Corrosion Behavior of Commercial Aluminum Alloy Processed by Equal Channel Angular Pressing

Precipitation behaviors and mechanical properties of a solution-treated Mg-Gd-Nd-Zn-Zr alloy during equal-channel angular pressing process

Correlation of microstructure, mechanical properties and corrosion behavior in a Ni34Co28Cr28Al10 multi-principal element alloy with outstanding corrosion resistance

Study on the Effect of the ECAP Deformation on the Organization and Properties of the Extruded Mg-Sn-Al Alloys

Microstructure and corrosion behavior of as-homogenized and as-extruded Mg−xLi−3Al−2Zn−0.5Y alloys (x=4, 8, 12)

Microstructure and Corrosion Behavior of the As-cast Mg-xAl (x=9%, 12%, 15%) Alloys

Mechanical Properties of Biomedical Ultrafine Grained Mg-3Sn-0.5Mn Alloy Processed by Equal-Channel Angular Pressing

Exfoliation Corrosion of As-Extruded Mg–1Li–1Ca: the Influence of the Superficial Layer