Abstract:In this paper, the substitution of different amounts of Zr for Ti in the hydrogen storage electrode alloy Mg35Ti10Ni55 has been carried out for the purpose of further improving the electrochemical performance of the electrode alloy. The electrochemical properties were tested on the purposely prepared Mg35Ti10−xZrxNi55 (x=1, 3, 5, 7, 9) electrode alloys. The results showed that all alloys substituted with Zr possessed a higher cycling capacity retention and a larger initial discharge capacity (except Mg35Ti1Zr9Ni55) than the original alloy Mg35Ti10Ni55. Among these alloys Mg35Ti5Zr5Ni55 exhibited the highest discharge capacity and cycling stability. It was found from X-ray Photoelectron Spectroscopy (XPS) surface analysis that the Zr content reduced the degree of oxidation of Mg. The higher the Zr content, the lower is the degree of oxidation of Mg. Auger electron spectroscopy (AES) analysis revealed that the thickness of the passive oxide film coating on the alloy surfaces became first reduced as the Zr content increased but subsequently became augmented as the Zr content exceeded 5 at.%. The study indicated that the corrosion inhibiting effect of Zr alone, without the presence of Ti was weak. The synergetic effect of Zr and Ti made the passive film more compact, less pervious and more protective than by Ti or Zr alone. The thickness of the passive film agreed well with the polarization resistance of the alloys obtained from electrochemical impedance spectroscopy (EIS) Nyquist diagrams, suggesting that the surface polarization resistance RP being closely related to the film thickness and the exchange current density on the surface of the alloy varied accordingly. The conclusion of this study is that 5 at.% Zr substitution in Mg35Ti10Ni55 leads to the formation on the surface of a good and thin passive film, which retards the corrosion of the alloy and at the same time leads to the least polarization resistance and highest exchange current in this series of alloys studied.

Effects of Alloying Elements on the Corrosion Behavior and Discharge Performance of Al-Zn-Mg-In-Ti-Sn Sacrificial Anode

Electrochemical Performance of Al-Mg Based Sacrificial Anodes

Intelligentization of traditional sacrificial anode Zn by Mg-alloying for reinforcing steel

Establishment of electrode potential-composition plot of Al-Mg-Zn alloys and sacrificial anode protection tests

The effect of partial substitution of Ti with Zr, Cr or V in the Mg35Ti10Ni55 electrode alloy on its electrochemical performance

The influence of Sn content on the electrochemical performance and discharge characteristics of Al-0.2Mg-0.02In-xSn-0.02Bi alloy anodes in aluminum-air batteries

Effects of Zn/Ca alloying on the Second Phase, Corrosion Behavior and Mg‐air Battery Anodic Performance of Mg‐1Sn‐based Alloys

The effect of partial substitution of Zr for Ti on the electrochemical properties and surface passivation film of Mg35Ti10 - xZrxNi55 (x=1, 3, 5, 7, 9) electrode alloys

Discharge performance of the Al–Mg–Sn alloy anodes with different Sn content for Al-air batteries

Dissolution of Nanoprecipitate on Aluminum-Alloy Anode for High Discharging Performance in Al Battery Applications

Effects of Solid-Solute Magnesium and Stannate Ion on the Electrochemical Characteristics of a High-Performance Aluminum Anode/electrolyte System

Discharge performance of Al-0.1Sn-0.1In-0.05Ga alloy for Al–air battery anodes

Effect of Sm Addition on the Electrochemical Behavior and Discharge Performance of Mg-1Sn-1Ca-0.3Mn Alloy as Mg-Air Battery Anodes

Effects of Intermetallic-Forming Element Additions on Microstructure and Corrosion Behavior of Sn–Zn Solder Alloys

Effects of SnO 2 Passive Film and Surface Micro-Galvanic Corrosion on the Corrosion Behavior of as-Extruded Mg-9Li-5Al-xSn Alloys

Effect of Sn/Ca Mass Ratio on the Second Phase, Corrosion Behavior and Discharge Performance of Mg–xSn–1Ca Mg–Air Battery Anodes

Effects of Heat Treatment on Microstructure and Electrochemical Performance of Al-Zn-Sn-Ga Alloy

Alloying effects on inhibiting hydrogen evolution of Zn metal anode in rechargeable aqueous batteries

Enhancing the Electrochemical Performance of Al-Mg-Sn-Ga Alloy Anode for Al-Air Battery by Solution Treatment

Role of micro-Ca/In alloying in tailoring the microstructural characteristics and discharge performance of dilute Mg-Bi-Sn-based alloys as anodes for Mg-air batteries

Alloying strategy to stabilize monocrystalline zinc anode under high utilization and working capacity