Abstract:In this work, five alloys, Al − Mg, Al − Ce, Al − Ti, Al − Mg − Ce and Al − Mg − Ti, were prepared, and the electrochemical properties and discharge behavior of pure Al and these alloys were investigated in 4 M KOH solution. Corrosion experiments and electrochemical tests were performed, including open circuit potential test, electrochemical impedance spectroscopy test and polarization curve test. The performance of Al − air batteries based on these anodes was investigated by constant current discharge and V − j discharge tests. The surface state of the Al anodes after discharge was analyzed by scanning electron microscope and energy dispersive spectrometer. The results show that the addition of magnesium, cerium, and titanium to Al enhances its corrosion resistance, discharge voltage, peak power density, and specific capacity. Among the binary alloys, Al − Mg demonstrates superior corrosion resistance and higher no − load activity, while Al − Ce and Al − Ti exhibit higher discharge voltages and peak power densities. Additionally, the ternary alloys Al − Mg − Ce and Al − Mg − Ti, prepared using Al − Mg as the matrix, significantly reduce the corrosion rate and improve discharge performance. Al − Mg − Ce shows a maximum voltage of 1.21 V at 50 mA·cm − 2 , while Al − Mg − Ti displays a maximum voltage of 0.899 V at 100 mA·cm − 2 , with a peak power density of 97.0 mW·cm − 2 , surpassing that of Al − Mg − Ce (83.4 mW·cm − 2 ) and pure Al (72.8 mW·cm − 2 ). However, Al − Mg − Ti exhibits lower anode utilization compared to all binary alloys, while Al − Mg − Ce demonstrates higher anode utilization than Al − Mg, albeit slightly lower than that of Al − Ce and Al − Ti. The study highlights the potential of Al − Mg − Ce and Al − Mg − Ti alloys as effective strategies to enhance the performance of Al − air batteries. These findings contribute to the advancement of high − performance Al anodes and the optimization of Al − air battery design.

The Effect of Extrusion Ratio on the Discharge and Corrosion Behavior of Mg-3Al-2.8Y-0.7Mn Alloy

Tailoring the electrochemical behavior and discharge performance of Mg–Al–Ca–Mn anodes for Mg-air batteries by different extrusion ratios

Microstructure and discharge performance of Mg–6Al and Mg–6Al-0.5Er alloys

Discharge and corrosion behavior of Mg–2Zn–Mn–xY alloys as the anode for Mg-air battery

Elucidating the dependence of electrochemical behavior and discharge performance on the grain structure of lean Mg-0.3Bi-0.3Ag-0.3In anodes in primary Mg-air battery

The Dependence of Electrochemical Behavior and Discharge Performance on the Zn/Gd Ratio of Mg-Li-Zn-Gd Anodes for Mg-Air Batteries

Tailoring the discharge performance of extruded Mg-Sm-Al anode for Mg-air battery applications via control of Al content

Effects of Grain Size on the Corrosion and Discharge Behaviors of Mg–Y Binary Alloys for Mg-Air Batteries

Discharge performance of extruded Mg-Bi binary alloys as anodes for primary Mg-air batteries

Processing Micro-Alloyed Mg-La Binary Alloy into a High-Performance Mg-Air Battery Anode via Extrusion

The effect of partial substitution of Ti with Zr, Cr or V in the Mg35Ti10Ni55 electrode alloy on its electrochemical performance

Effect of Y content on performance of AZ31 magnesium alloy anode in air battery

An electrochemical investigation of mechanical alloying of MgNi-based hydrogen storage alloys

Discharge performance of Mg-Y binary alloys as anodes for Mg-air batteries

The influence of cerium or titanium addition on the corrosion resistance and discharge performance of Al − mg anode for aluminum − air batteries

Tailoring the microstructure and improving the discharge properties of dilute Mg-Sn-Mn-Ca alloy as anode for Mg-air battery through homogenization prior to extrusion

Linking the discharge behavior and microstructure of ternary Mg–Ca–Zn alloy anodes for magnesium-air cells

Improving the electrochemical behaviors and discharge performance of as-rolled Mg-4Li alloys through multicomponent alloying

Discharge Properties and Electrochemical Behaviors of Mg-Zn-xSr Magnesium Anodes for Mg–Air Batteries

Effect of Extrusion on Mechanical Property, Corrosion Behavior, and In Vitro Biocompatibility of the As-Cast Mg-Zn-Y-Sr Alloy

The Synergistic Effect of Trace Ag and Hot Extruding on the Microstructure and Properties of a Biodegradable Mg-Zn-Sr-Ag Alloy