Abstract:The effects of a minor Zn addition on the mechanical and corrosion properties and microstructure of a high Mg content AlMg alloy containing Er and Zr in the warm-rolled state were studied using tensile test, nitric acid mass loss test (NAMLT), exfoliation corrosion susceptibility test (ASSET), scanning electron microscopy (SEM) and transmission electron microscopy (TEM) techniques. The tensile test results showed that the 0.58 wt% Zn addition to the Al-Mg-Er-Zr alloy increased the yield strength from 297 to 351 MPa and tensile strength from 416 to 445 MPa, but decreased the elongation from 13.3 % to 12.5 %. The NAMLT and ASSET results showed that the two warm rolled alloys were initially in the stabilization state, but the Al-Mg-Er-Zr alloy without Zn added became sensitized severely after the accelerated sensitization annealing (ASA) at 100 °C. The Zn addition improved the intergranular corrosion (IGC) resistance and exfoliation corrosion (EC) resistance significantly. The TEM results showed that, for the Al-Mg-Er-Zr alloy, there were Al 3 (Er,Zr) phase particles in the matrix and β (Al 3 Mg 2 ) phase particles separated from each other at the grain boundary. After the ASA treatment, more β phase particles were precipitated and covered the grain boundary completely. For the Al-Mg-Zn-Er- Zr alloy, another nanoscale T (Al 32 (Mg, Zn) 49 ) phase was precipitated in the matrix, and there were no grain boundary phase particles observed at the grain boundary, because the precipitation of T phase consumed the supersaturated Mg in the matrix, thus suppressing the formation of grain boundary phase particles during the ASA treatment and resulting in a good corrosion resistance. The strengthening effect of the Zn addition was mainly due to the formation of T phase particles during the warm rolling process.

Effects of grain size and Al-Mn phase on the corrosion performance of hot-rolled AZ31 magnesium alloy

The Effect of Texture on the Corrosion Behavior of AZ31 Mg Alloy

Effect of rolling temperature on microstructure and mechanical properties of hot-rolled Mg-Al-Ca-Zn-Mn alloys

Influence of Hot Rolling on Microstructure, Corrosion and Mechanical Properties of Mg–Zn–Mn–Ca Alloy

Microstructure Characteristics and Corrosion Behaviors of Mg-2Zn-2Er-0.3Zr-0.3Mn Alloy under Various Rolling Reductions

Recrystallization Behavior and Mechanical Properties of Az31b Alloy During the Hot-Rolling Process

Effect of Rolling Temperature on Microstructure and Properties of Al-Mg-Li Alloy

Effect of Rolling Ratios on the Microstructural Evolution and Corrosion Performance of an As-Rolled Mg-8 Wt.%li Alloy

Effect of Rolling Treatment on Microstructure, Mechanical Properties, and Corrosion Properties of WE43 Alloy

Evolution of the Microstructure and Mechanical Properties of AZ31 Magnesium Alloy Sheets during Multi-Pass Lowered-Temperature Rolling

Effects of Rolling-Cryogenic Process on Microstructure and Mechanical Properties of AZ31 Magnesium Alloy Sheets

The influence of rolling on the corrosion and wear resistance of the MAO coating on ZM5 alloy

The effect of grain size on texture evolution and mechanical properties of an AZ31 magnesium alloy during cold-rolling process

Microstructure and mechanical property of multi-pass low-strain rolled Mg-Al-Zn-Mn alloy sheet

Effect of Al/Mn ratio on corrosion behavior of lean Mg-Zn-Ca-Al-Mn alloy processed by twin-roll casting

Microstructure, Mechanical, and Corrosion Properties of Mg-Zn-Ga Alloy after Hot Rolling

High corrosion resistance and weak corrosion anisotropy of an as-rolled Mg-3Al-1Zn (in wt.%) alloy with strong crystallographic texture

The influence of Zn addition on the microstructure and mechanical and corrosion properties of warm rolled Al mg alloys containing Er and Zr

Microstructure, mechanical properties and deformation mechanism of powder metallurgy AZ31 magnesium alloy during rolling

An experimental and theoretical investigation of the effect of second-phase particles on grain growth during the annealing of hot-rolled AZ61 magnesium alloy

Achieving ultra-fine grains and high corrosion resistance of Al-Zn-Mg-Cu alloy by ECAP and post cold rolling