Abstract:The bottleneck problems of SiC particles reinforced AlSi10Mg composites (SiC/AlSi10Mg) prepared by traditional casting method, such as composition segregation, interface reaction and coarse microstructure, can be effectively improved by powder metallurgy with lower processing temperature. In this study, the influence of SiC particle size and content on the properties of SiC/AlSi10Mg was systematically analyzed. SiC/AlSi10Mg composites were prepared by planetary ball milling, spark plasma sintering (SPS) and hot extrusion composite preparation process. The obtained composites presents dense microstructure without the formation of interfacial reaction phase. The distribution of micron SiC particles (μm-SiC) in the matrix is relatively uniform, and nano SiC particles (nm-SiC) slightly agglomerates with the increase of the content. The strength of SiC/AlSi10Mg increases with the increase of nm-SiC content, which is mainly attributed to dispersion strengthening, dislocation strengthening and grain refinement strengthening. The strength of SiC/AlSi10Mg hardly changes with the increase of μm-SiC content, but the elongation decreases gradually. The deformation between μm-SiC and AlSi10Mg matrix is not coordinated and μm-SiC cleave the AlSi10Mg matrix. The irregular boundaries of μm-SiC are easy to produce stress concentration during loading, leading to interface cracking or μm-SiC fracture. Therefore, μm-SiC are difficult to play a significant strengthening effect to composites. With the increase of SiC content, the fracture mechanism of composites gradually changes from ductile fracture to brittle fracture in SiC agglomeration region. This study lays a theoretical and experimental foundation for the controllable preparation and performance optimization of high strength and toughness AMCs reinforced by SiC particles.

Synthesis of SiC@Al2O3 core–shell nanoparticles for dense SiC sintering

Preparation of SiC@Al2O3–Y2O3 core-shell nanoparticles by a slow precipitation method for dense SiC sintering

Improved Sintering Ability of SiC Ceramics from SiC@Al2O3 Core-Shell Nanoparticles Prepared by a Slow Precipitation Method

Optimization of Microstructure to Improve Si3n4 Ceramics with Thermal Conductivity and Mechanical Properties: Effect of Si and Α-Si3n4 Powder Composition

Enhanced strength and toughness of SiC/C composite ceramics via SiC@graphene core–shell nanoparticles

In-situ synthesis of nano SiC particles in Al–Si–C system at 750 °C

An Insight into Sintering Mechanisms of Silicon Carbide Nanoparticles with Additives Using MD Simulation

Densification and Enhancement of Sic Particulate Reinforced Fine Grain Sic Ceramic

Microstructure and mechanical properties of SiC-Al2O3 nanocomposite prepared by surface modified SiC nanopowders

Preparation of SiC-AlN Ceramic Alloy Powder by Direct Reaction Between Constituent Elements and Property Evaluation of Its Sintered Compacts.

Controllable Synthesis of SiC@Graphene Core‐shell Nanoparticles Via Fluidized Bed Chemical Vapor Deposition

Synthesis of SiC-AlN Powder and Characterization of Its HIP-Sintered Compacts.

Densification and Mechanical Properties of Si3N4/SiC Nanocomposite Using Si-Nitrided Si3N4 Powder

Synthesis and properties of porous SiN/SiC nanocomposites by carbothermal reaction between SiN and carbon

Synthesis of SiC-AlN Ceramic Alloy Powder by the Direct Reactions Between the Constituent Elements.

Synthesis of fine grain Ti3SiC2 by spark plasma sintering with additive of aluminum

Preparation and Characterization of Core–shell Structured Co/SiO2 Nanosphere

Influence of SiO2 addition on the sintering behavior and kinetics of fine-sized α-Al2O3 nanoparticles

Effect of Sintering Temperature on Properties of Porous SiC Ceramics Produced Through Coat-mix/Composite Additives Process

Preparation and properties of intragranular Al2O3-SiC nanocomposites

Influence of characteristic parameters of SiC reinforcements on mechanical properties of AlSi10Mg matrix composites by powder metallurgy