Abstract:Developing high strength and tough silicon carbide (SiC) composite ceramics remains a significant challenge. Here, we report the process of synthesizing fully densified SiC/C composite ceramics using SiC@graphene (SiC@G) core–shell nanoparticles as raw materials through spark plasma sintering (SPS) at 1700°C and 45 MPa. The SiC@G nanoparticles were synthesized by the fluidized bed chemical vapor deposition (FB‐CVD) method. During the sintering process, graphene coated, the surface of nanosized SiC particles exhibited high electrical and thermal conductivity, facilitating the uniform distribution of pulse current and heat and promoting the densification of SiC/C composite ceramics. For the prepared SiC/C composite ceramic, the carbon content reaches as high as 14.3 wt%, with carbon uniformly dispersed in a particulate form within the SiC matrix and stable interface bonding. Consequently, the introduction of excessive carbon does not compromise the hardness (28.8 GPa) and flexural strength (517.34 MPa) of the SiC/C composite ceramics. Furthermore, the carbon particles effectively enhance the toughness of the SiC/C composite material through mechanisms such as crack branching, bridging, and deflection, resulting in a fracture toughness of 7.38 MPa m1/2. The preparation strategy in this study provides a novel route for sintering SiC composites with high‐carbon content through nanoscale powder structure design, resulting in the attainment of high‐performance lightweight composite materials.

Improved Sintering Ability of SiC Ceramics from SiC@Al2O3 Core-Shell Nanoparticles Prepared by a Slow Precipitation Method

Preparation of SiC@Al2O3–Y2O3 core-shell nanoparticles by a slow precipitation method for dense SiC sintering

Synthesis of SiC@Al2O3 core–shell nanoparticles for dense SiC sintering

Optimization of Microstructure to Improve Si3n4 Ceramics with Thermal Conductivity and Mechanical Properties: Effect of Si and Α-Si3n4 Powder Composition

Microstructure and mechanical properties of SiC-Al2O3 nanocomposite prepared by surface modified SiC nanopowders

Preparation and properties of intragranular Al2O3-SiC nanocomposites

Effects of Al2O3@Ni core-shell powders on the microstructure and mechanical properties of Ti(C,N) cermets via spark plasma sintering

Effect of Sintering Temperature on Properties of Porous SiC Ceramics Produced Through Coat-mix/Composite Additives Process

Influence of SiC particle size on microstructure and mechanical properties of Al2O3-SiC nanocomposites

SiC-Al_2O_3 Nanocomposites Superfast Densified by SPS

Surface Modification Of Nano-Sic Powders By Coating With Heterogeneous Nucleation Process

Preparation and sintering behaviour of nanostructured alumina/titania composite powders modified with nano-dopants

Effect of SiCP Content on β-SiAlON/SiC Nanocomposite Ceramic

Effect of Α-Al2o3 Coatings on the Interface of Ni/SiC Composites Prepared by Electrodeposition

Effect of Al(OH)<sub>3</sub> Addition on the Properties of SiC/Al<sub>2</sub>O<sub>3</sub> Composite Porous Ceramics

Preparation and Properties of Porous Silicon Carbide Ceramics Through Coat-Mix and Composite Additives Process

Enhanced strength and toughness of SiC/C composite ceramics via SiC@graphene core–shell nanoparticles

Precipitation behavior and mechanical properties of Al-Zn-Mg-Cu matrix nanocomposites: Effects of SiC nanoparticles addition and heat treatment

Silicon carbide particle size effects in Al2O3-SiC nanocomposites

Effect of SiC Addition on Mechanical Properties of Hot-Pressed Al2O3-GdAlO3 Ceramics with Eutectic Composition

PREPARING Si3N4 CERAMICS WITH HIGH PERFORMANCES BY GELCASTING (I)INFLUENCE OF COATING Si3N4 POWDER ON MECHANICAL PROPERTIES OF THE MATERIAL