Abstract:We present a solid‐state processing pathway for ultrahigh molecular weight polyethylene, a high‐end engineering polymer that cannot be melt processed. Ultra‐high molecular weight polyethylene (UHMWPE) stands out as the preferred material across a wide spectrum of demanding applications, thanks to its remarkable mechanical, chemical and physical attributes. Nevertheless, processing UHMWPE can be an arduous and time‐consuming endeavor. Traditional melt‐processing techniques, commonly employed for polymers, prove impractical due to the exceedingly high viscosity of the melt that follows from the highly entangled macromolecular chains. Several methods are known to lower the entanglement density of UHMWPE, such as crystallization from a semidilute solution or direct polymerization, resulting in a less interconnected polymer structure. Unfortunately, even with low‐entangled UHMWPE, melt processing remains unviable because of the rapid re‐entanglement of polymer chains upon melting. However, these low‐entangled UHMWPE materials can still be effectively processed in the solid state, a technique employed in the production of high‐performance UHMWPE fibers and tapes, currently the only two feasible geometries. This research reports the development of a solid‐state extrusion method for nascent low‐entangled powder, centering on manipulating the surface energy of the interior wall materials within the extruder and die. Ordinary steel dies proved ineffective for solid‐state extrusion, as they generated excessive friction between the die and UHMWPE, resulting in a rapidly escalating extrusion pressure. However, utilizing dies constructed from temperature‐resistant polymers allowed for extrusion at a consistent pressure without the need for lubricating agents. We demonstrate the practicality of the developed solid‐state extrusion method by fabricating UHMWPE monofilaments and tubes, showcasing its potential in expanding the range of producible UHMWPE geometries. Additionally, a first evaluation of the influence of processing conditions and the entanglement density of the reactor powder used on extrudability, and the properties of the resulting components is presented. Highlights A process for the solid‐state extrusion of UHMWPE is developed. UHMWPE processing with higher design flexibility than current industrial standards. UHMWPE processing with higher throughput than current industrial standards. Contrary to previous techniques no lubricating agent or co‐extrudate is used.

Properties of Compression Molded Ultra‐high Molecular Weight Polyethylene Products Pretreated by Eccentric Rotor Extrusion

Mechanical properties and biocompatibility of melt processed, self-reinforced ultrahigh molecular weight polyethylene.

Structure and properties of ultrahigh molecular weight polyethylene processed under a consecutive elongational flow

Self-reinforced polyethylene blend for artificial joint application.

Melt Processing and Structural Manipulation of Highly Linear Disentangled Ultrahigh Molecular Weight Polyethylene

Short-time fabrication of well-mixed high-density polyethylene/ultrahigh-molecular-weight polyethylene blends under elongational flow: morphology, mechanical properties and mechanism: Fabrication and performance of HDPE/UHMWPE blends under elongational flow

Ultra High Molecular Weight Polyethylene with Improved Plasticity and Toughness by High Temperature Melting

Tuning the Superstructure of Ultrahigh-Molecular-Weight Polyethylene/Low-Molecular-Weight Polyethylene Blend for Artificial Joint Application

Elongational Flow Field Processed Ultrahigh Molecular Weight Polyethylene/Polypropylene Blends with Distinct Interlayer Phase for Enhanced Tribological Properties

Simultaneously Improving Wear Resistance and Mechanical Performance of Ultrahigh Molecular Weight Polyethylene Via Cross-Linking and Structural Manipulation

High-Temperature Melted, Cross-Linked, and Stabilized Ultrahigh Molecular Weight Polyethylene

Enhancing Chain Mobility of Ultrahigh Molecular Weight Polyethylene by Regulating Residence Time under a Consecutive Elongational Flow for Improved Processability

Realizing Mechanically Reinforced All-Polyethylene Material by Dispersing UHMWPE Via High-Speed Shear Extrusion

Synergic Enhancement of High-density Polyethylene Through Ultrahigh Molecular Weight Polyethylene and Multi-flow Vibration Injection Molding: A Facile Fabrication with Potential Industrial Prospects

Achieving injection molding interlayer strength via powder assisted hot isostatic pressing in material extrusion polyetheretherketone

Advances in Enhancing Mechanical Performance of Ultrahigh Molecular Weight Polyethylene Used for Total Joint Replacement

Improved Properties of Metallocene Polyethylene/Poly(ethylene Terephthalate) Blends Processed by an Innovative Eccentric Rotor Extruder

Improved Performance Balance of Polyethylene by Simultaneously Forming Oriented Crystals and Blending Ultrahigh-Molecular-Weight Polyethylene

Structure and Properties of UHMWPE Products Strengthened and Toughened by Pulse Vibration Molding at Low Temperature

Solid‐state extrusion of nascent disentangled ultra‐high molecular weight polyethylene

High Wear Resistance of Metallocene Polyethylene with Long-Chain Branch for Artificial Joints