Abstract:Purpose Polyetheretherketone (PEEK) is used to manufacture biomedical implants because it has a high strength-to-weight ratio and high strength and is biocompatible. However, the use of fused deposition modeling to print a PEEK results in low strength and crystallinity. This study aims to use the Taguchi method to optimize the printing factors to obtain the highest tensile strength of the printed PEEK object. The annealing effect on printed PEEK object and crystallinity are also investigated. Design/methodology/approach This study determines the printing factors including the printing speed, layer thickness, printing temperature and extrusion width. Taguchi experimental design with a L9 orthogonal array is used to print the tensile specimen and carried out the tensile test to compare the tensile strength and porosity. Analysis of variance (ANOVA) is used to determine the experimental error and to determine the optimization printing parameters to obtain the highest tensile strength. A multivariate linear regression analysis is used to obtain the linear regression equation for predicting the theoretical tensile strength. An X-ray analysis is achieved to evaluate the crystalline of printed object. The effect of annealing is investigated to improve the tensile strength of printed part. An intervertebral lumber device is printed to demonstrate the feasibility of the obtained optimization parameters for practical application. Findings Taguchi experiment designs nine sets of parameters to print the PEEK tensile specimen. The experimental results and the ANOVA present that the order in which the factors affect the tensile strength for printed PEEK parts is the layer thickness, the extrusion width, the printing speed and the printing temperature. The optimized printing parameters are a printing speed of 5 mm/s, a layer thickness of 0.1 mm, a printing temperature of 395 °C and an extrusion strand width of 0.44 mm. The average tensile strength of printed specimen with the optimized printing parameters is 91.48 MPa, which is slightly less than the theoretical predicted value of 94.34 MPa. After annealing, the tensile strength increases to 98.85 MPa, which is comparable to that for molded PEEK and the porosity decreases to 0.3 from 3.9%. X-ray diffraction results show that all printed and annealed specimens have a high degree of crystallinity. The printed intervertebral lumber device has ultimate compressive load of 13.42 kN. Originality/value The optimized printing parameters is suitable for low-price fused deposition modeling machine because it does not involve a table at high temperature and can print the PEEK object with high tensile strength and good crystalline. Annealing parameters offer a good solution for tensile strength improvement.

Achieving injection molding interlayer strength via powder assisted hot isostatic pressing in material extrusion polyetheretherketone

The microstructural evolution of material extrusion based additive manufacturing of polyetheretherketone under different printing conditions and application in a spinal implant

Optimizing Fused Deposition Molding Process Parameters for Improving Forming Strength of Polyetheretherketone

An experimental investigation on the tensile properties of PEEK-PEI sandwich structures prepared via fused filament fabrication

Optimization of FDM 3D printing parameters for high strength PEEK using the Taguchi method and experimental validation

Effect of PEEK Fused Deposition Modeling Temperature on Tensile Properties of Parts

Microinjection Moulded Polyetheretherketone Biomaterials As Spinal Implants: Physico-Chemical and Mechanical Characterisation

Molding of polyether ether ketone (PEEK) and its composites: a review

Effects of processing parameters and annealing on the mechanical properties of polyether ether ketone(PEEK) via fused deposition modeling(FDM)

Superior strength in the 3D ‐printed polyether‐ether‐ketone composites reinforced by annealing and carbon fibers

Mechanical performance of PEEK-Ti6Al4V interpenetrating phase composites fabricated by powder bed fusion and vacuum infiltration targeting large and load-bearing implants

Influence of Polyether Ether Ketone (PEEK) Viscosity on Interlayer Shear Strength in Screw Extrusion Additive Manufacturing

Preparation And Characterization Of High-Strength Poly( Ether Ether Ketone) Films

Microcellular injection molding of polyether-ether-ketone

Preliminary Investigation Of Poly-Ether-Ether-Ketone Based On Fused Deposition Modeling For Medical Applications

Effect of 3D Printing Process Parameters and Heat Treatment Conditions on the Mechanical Properties and Microstructure of PEEK Parts

Bi-directional regulatable mechanical properties of 3D braided polyetheretherketone (PEEK)

Improved design of fused deposition modeling equipment for 3D printing of high-performance PEEK parts

Strategies to Improve the Performance of Polyetheretherketone (PEEK) As Orthopedic Implants: from Surface Modification to Addition of Bioactive Materials.

A novel printing strategy to fabricate polyetheretherketone (PEEK)-based composites via hollow filaments filled with multiple reinforcements

Material Extrusion 3D Printing of PEEK-Based Composites