Abstract:Polymers reinforced with conducting fibers to achieve electrical conductivity have attracted remarkable attention in several engineering applications, and injection molding provides a cost-effective way for mass production. However, the electrical performance usually varies with the molding conditions. Moreover, high added content of conducting fibers usually results in molding difficulties. In this study, we propose using microcellular (MuCell) injection molding for polypropylene (PP)/carbon fiber (CF, 20, and 30 wt%) composites and hope that the MuCell injection molding process can improve both electrical and mechanical performance as compared with conventional injection molded (CIM) parts under the same CF content. Both molding techniques were also employed with and without gas counter pressure (GCP), and the overall fiber orientation, through-plane electrical conductivity (TPEC), and tensile strength (TS) of the composites were characterized. Based on the various processing technologies, the results can be described in four aspects: (1) Compared with CIM, microcellular foaming significantly influenced the fiber orientation, and the TPECs of the samples with 20 and 30 wt% CF were 18-78 and 5-8 times higher than those of the corresponding samples molded by CIM, respectively; (2) when GCP was employed in the CIM process, the TPEC of the samples with 20 and 30 wt% CF increased by 3 and 2 times, respectively. Similar results were obtained in the case of microcellular injection molding-the TPEC of the 20 and 30 wt% composites increased by 7-74 and 18-32 times, respectively; (3) although microcellular injection molding alone (i.e., without GCP) showed the greatest influence on the randomness of the fiber orientation and the TPEC, the TS of the samples was the lowest due to the uncontrollable foaming cell size and cell size uniformity; (4) in contrast, when GCP was employed in the microcellular foaming process, high TS was obtained, and the TPEC was significantly enhanced. The high foaming quality owing to the GCP implementation improved the randomness of fiber orientation, as well as the electrical and mechanical properties of the composites. Generally speaking, microcellular injection combined with gas counter pressure does provide a promising way to achieve high electrical and mechanical performance for carbon-fiber-added polypropylene composites.

Microcellular injection molding of polyether-ether-ketone

Effect of Mold Opening on Microcellular Polyether-Ether-ketone Fabricated by Injection Molding

Fabrication of Polyether–Ether–Ketone Foams with Superior Properties and Mitigated Weld Lines by Microcellular Injection Molding

Achieving injection molding interlayer strength via powder assisted hot isostatic pressing in material extrusion polyetheretherketone

Processing Effects on the Through-Plane Electrical Conductivities and Tensile Strengths of Microcellular-Injection-Molded Polypropylene Composites with Carbon Fibers

Microcellular injection molding of foamed engineering plastic parts with high dimensional accuracy

Fabrication of lightweight polyethersulfone foams with enhanced surface quality and high specific flexural properties using micro‐opening microcellular injection molding

Rapid mold temperature rising method for PEEK microcellular injection molding based on induction heating

Lightweight and High Impact Toughness PP/PET/POE Composite Foams Fabricated by In Situ Nanofibrillation and Microcellular Injection Molding

Molding process and properties of polyimide-fiber-fabric-reinforced polyether ether ketone composites

Molding of polyether ether ketone (PEEK) and its composites: a review

Crystallinity and mechanical properties of polypropylene products foamed by microcellular injection molding process

Conventional and Microcellular Injection Molding of a Highly Filled Polycarbonate Composite with Glass Fibers and Carbon Black

Microextrusion Foaming of Polyetheretherketone Fiber: Mechanical and Thermal Insulation Properties

Microcellular injection molding process for producing lightweight thermoplastic polyurethane with customizable properties

High-strength, impact-resistant PP/PTFE composite foam with enhanced surface appearance achieved through mold-opening microcellular injection molding

Micro-Injection Molding of Carbon-Fiber-Reinforced Plastic (CFRP)/Polymethyl Methacrylate (PMMA) Composite Components

Real-microcellular poly(ether-block-amide)/carbon fiber foams with improved mechanical property and surface quality for high-performance electromagnetic interference shielding applications

Effect of molecular weight on mechanical properties and microstructure of 3D printed poly(ether ether ketone)

Effect of Micro-Mold Cavity Dimension on Structure Andproperty of Polylactic Acid/Polycaprolactone Blend Undermicroinjection Molding Conditions

The Cellular Structure and Mechanical Properties of Polypropylene/Nano-CaCO3/Ethylene-propylene-diene-monomer Composites Prepared by an In-Mold-Decoration/Microcellular-Injection-Molding Process